Lucent Technologies R5SI Manual Do Utilizador
DEFINITY Enterprise Communications Server Release 5
Maintenance and Test for R5vs/si
Maintenance and Test for R5vs/si
555-230-123
Issue 1
April 1997
Maintenance Object Repair Procedures
Page 10-65
ANL-LINE (8-Port Analog Line), ANL-NE-L (8-Port Neon Analog Line)
10
ANL-LINE (8-Port Analog Line),
ANL-NE-L (8-Port Neon Analog Line)
ANL-NE-L (8-Port Neon Analog Line)
The 8-Port Analog Line circuit packs are:
These circuit packs provide eight ports for single line on-premises or
off-premises analog endpoints such as analog voice terminals, queue warning
level lamps, recorded announcements, dictation machines, PagePac
off-premises analog endpoints such as analog voice terminals, queue warning
level lamps, recorded announcements, dictation machines, PagePac
™
paging
equipment, external alerting devices, modems, facsimile machines, and AUDIX
voice ports. The TN769 supports a neon message waiting lamp. The other
eight-port analog lines do not support the lamp.
voice ports. The TN769 supports a neon message waiting lamp. The other
eight-port analog lines do not support the lamp.
Test #48 may cause some terminal equipment to ring briefly during daily
maintenance. If this ringing is disturbing the customer or the terminal equipment,
it should be disabled using the Tests field of the station administration screen.
However, on some releases of the software, this action disables Tests #6, #47,
and #35 as well as Test #48. Test #47 may cause a false alarm when the port is
connected to off-premises equipment, some non-voice terminal equipment, and
some loop equipment. If this is the case, then the test should be disabled using
the Tests field of the
maintenance. If this ringing is disturbing the customer or the terminal equipment,
it should be disabled using the Tests field of the station administration screen.
However, on some releases of the software, this action disables Tests #6, #47,
and #35 as well as Test #48. Test #47 may cause a false alarm when the port is
connected to off-premises equipment, some non-voice terminal equipment, and
some loop equipment. If this is the case, then the test should be disabled using
the Tests field of the
change station <extension>
command.
No maintenance of the terminal connected to the 8-Port Analog Line circuit pack
or 8-Port Neon Analog Line circuit pack is performed, except to determine
whether or not the terminal is connected. Failures of the neon message waiting
lamp power (for ANL-NE-L only) and the common ringing application circuitry are
or 8-Port Neon Analog Line circuit pack is performed, except to determine
whether or not the terminal is connected. Failures of the neon message waiting
lamp power (for ANL-NE-L only) and the common ringing application circuitry are
1.
Where P is the port network number (1 for PPN and 2 or 3 for EPN); C is the carrier
designation (for example, A, B, C, D, or E); SS is the address of the slot in the carrier
where the circuit pack is located (for example, 01, 02, ..., etc.); and pp is the 2-digit
port number (for example, 01).
designation (for example, A, B, C, D, or E); SS is the address of the slot in the carrier
where the circuit pack is located (for example, 01, 02, ..., etc.); and pp is the 2-digit
port number (for example, 01).
MO Name (in
Alarm Log)
Alarm
Level
Initial Command to
Run
1
Full Name of MO
ANL-LINE
MIN
test port PCSSpp l
8-Port Analog Line
ANL-LINE
WRN
test port PCSSpp sh
8-Port Analog Line
ANL-NE-L
MIN
test port PCSSpp l
8-Port Neon Analog Line
ANL-NE-L
WRN
test port PCSSpp sh
8-Port Neon Analog Line
TN742
TN431 [G3iV2-386]
TN769
TN443 [G3iV2-386]
TN712
TN467 [G3iV2-386]
TN411 [G3iV2-386]