Campbell Hausfeld SDM-CAN Manual Do Utilizador
Section 3. Programming CR10X, CR7 and CR23X
3.4.2 Group Trigger
The group trigger function provides a mechanism to synchronise the data capture
by one or more SDM-CAN (and some other SDM devices too).
by one or more SDM-CAN (and some other SDM devices too).
This mode is enabled when an SDM-Group Trigger (P110) instruction is
encountered. When this instruction runs, it broadcasts a special SDM message
which causes all the SDM-CAN devices to copy the last data values captured from
the CAN-bus into the working data buffers, and no further updates are allowed
until P110 runs again (normally at the next execution of the program table). P118
instructions will read the locked values which are all sampled at once.
encountered. When this instruction runs, it broadcasts a special SDM message
which causes all the SDM-CAN devices to copy the last data values captured from
the CAN-bus into the working data buffers, and no further updates are allowed
until P110 runs again (normally at the next execution of the program table). P118
instructions will read the locked values which are all sampled at once.
This SDM-Group trigger command is normally positioned at the beginning of the
program table to lock all data samples exactly to the start of the scan interval. It
should be remembered, however, that in the case of the SDM-CAN it will simply
lock these values to the last values captured which could already have been
transmitted some time earlier.
program table to lock all data samples exactly to the start of the scan interval. It
should be remembered, however, that in the case of the SDM-CAN it will simply
lock these values to the last values captured which could already have been
transmitted some time earlier.
The SDM-Group trigger instruction actually broadcasts its message to SDM
address 33
address 33
4
(base 4), which prevents this address being available if the SDM-
Group trigger command is to be used. This effectively reduces the number of
SDM peripherals that support global trigger to 15 units.
SDM peripherals that support global trigger to 15 units.
3.4.3 Frame buffers with filtering and triggering
Operating systems V3 include the ability for the user data logger program to
attach a buffer of 256 frames to any receiving CAN ID up to a limit of 25 different
ID’s.
attach a buffer of 256 frames to any receiving CAN ID up to a limit of 25 different
ID’s.
If the user program tries to allocate more than 25 buffers then
the additional buffer allocations will be ignored.
the additional buffer allocations will be ignored.
NOTE
Each buffer can be configured as a standard ring buffer with no trigger or filter
associated with it. The buffer can also be set to start to capture data when a
predefined trigger pattern is encountered within the CAN data, or it can filter and
buffer only the CAN frames that have some part of the data that fits a pattern.
associated with it. The buffer can also be set to start to capture data when a
predefined trigger pattern is encountered within the CAN data, or it can filter and
buffer only the CAN frames that have some part of the data that fits a pattern.
To configure a filter or trigger two masks are used. The first is user defined as a 64
bit include AND mask applied to the CAN data of the CAN ID of interest. A
second 64 bit user defined pattern is compared with the CAN data and when it
matches the results of the previous `AND’ operation the buffer will either trigger
or filter CAN data of a specific ID until the buffer is full.
bit include AND mask applied to the CAN data of the CAN ID of interest. A
second 64 bit user defined pattern is compared with the CAN data and when it
matches the results of the previous `AND’ operation the buffer will either trigger
or filter CAN data of a specific ID until the buffer is full.
The buffer is a fill and stop ring buffer so if the buffer is full no more data will be
stored until the logger reads a frame and makes room for another frame to be
stored. With no mask and pattern bits set in trigger mode the buffer will trigger on
any frame and behave as a normal ring buffer. This is useful for collecting fast
back to back bursts of packets as the logger can collect them later in the
knowledge the SDM-CAN will have captured up to 256 packets and stored them
in its buffer.
stored until the logger reads a frame and makes room for another frame to be
stored. With no mask and pattern bits set in trigger mode the buffer will trigger on
any frame and behave as a normal ring buffer. This is useful for collecting fast
back to back bursts of packets as the logger can collect them later in the
knowledge the SDM-CAN will have captured up to 256 packets and stored them
in its buffer.
3-15