Yamaha YSP-40D Manual Do Utilizador
AUTO SETUP (IntelliBeam)
40
En
■
Error messages for AUTO SETUP
Before the AUTO SETUP procedure starts
While the AUTO SETUP procedure is in progress
If one of the errors listed below except E-1 is displayed, press RETURN. In case you have started the AUTO SETUP
procedure by pressing AUTO SETUP in step 3, run the procedure again from step 3 after the screen disappears. In case
you have started the AUTO SETUP procedure by pressing MENU in step 3, run the procedure again from step 4 after the
screen in step 3 is displayed. Run MANUAL SETUP if the problem is difficult to be saved.
procedure by pressing AUTO SETUP in step 3, run the procedure again from step 3 after the screen disappears. In case
you have started the AUTO SETUP procedure by pressing MENU in step 3, run the procedure again from step 4 after the
screen in step 3 is displayed. Run MANUAL SETUP if the problem is difficult to be saved.
Error message
Cause
Remedy
See
page
ERROR E-2
No MIC detected. Please check
MIC connection and re-try.
No MIC detected. Please check
MIC connection and re-try.
The IntelliBeam microphone is not
connected to this unit.
connected to this unit.
Connect the IntelliBeam microphone to
this unit.
this unit.
Error message
Cause
Remedy
See
page
ERROR E-1
Please test in quieter environment.
Please test in quieter environment.
There is too much unwanted noise in
your listening room.
your listening room.
Make sure that your listening room is as
quiet as possible. You may want to
choose certain hours during the day
when there is not much noise coming
from outside.
quiet as possible. You may want to
choose certain hours during the day
when there is not much noise coming
from outside.
—
ERROR E-2
No MIC detected. Please check
MIC connection and re-try.
No MIC detected. Please check
MIC connection and re-try.
The IntelliBeam microphone was
disconnected while the AUTO SETUP
procedure was in progress.
disconnected while the AUTO SETUP
procedure was in progress.
Make sure that the IntelliBeam
microphone is firmly connected to this
unit.
microphone is firmly connected to this
unit.
ERROR E-3
Unexpected control is detected.
Please re-try.
Unexpected control is detected.
Please re-try.
Some other operations were performed
on this unit while the AUTO SETUP
procedure was in progress.
on this unit while the AUTO SETUP
procedure was in progress.
Do not perform any other operations
while the AUTO SETUP procedure is in
progress.
while the AUTO SETUP procedure is in
progress.
—
ERROR E-4
Please check MIC position. MIC
should be set in front of YSP.
Please check MIC position. MIC
should be set in front of YSP.
The IntelliBeam microphone is not
placed in front of this unit.
placed in front of this unit.
Make sure that the IntelliBeam
microphone is installed in front of this
unit.
microphone is installed in front of this
unit.
ERROR E-5
Please check MIC position. MIC
should be set above 1.8m/6.0ft.
Please check MIC position. MIC
should be set above 1.8m/6.0ft.
The IntelliBeam microphone is not
placed in the right distance from this
unit.
placed in the right distance from this
unit.
Make sure that the IntelliBeam
microphone is installed more than 1.8 m
(6.0 ft) from the front of this unit and
within 1 m (3.3 ft) from the center height
of this unit.
microphone is installed more than 1.8 m
(6.0 ft) from the front of this unit and
within 1 m (3.3 ft) from the center height
of this unit.
ERROR E-6
Volume level is lower than
expected. Please check MIC
position/connection and re-try.
Volume level is lower than
expected. Please check MIC
position/connection and re-try.
The IntelliBeam microphone cannot
collect the sound produced by this unit
because the sound output level is too low.
collect the sound produced by this unit
because the sound output level is too low.
Make sure that the IntelliBeam
microphone is firmly connected to this
unit and placed in a proper location. If
the problem persists, contact the nearest
authorized Yamaha service center for
assistance.
microphone is firmly connected to this
unit and placed in a proper location. If
the problem persists, contact the nearest
authorized Yamaha service center for
assistance.
ERROR E-7
Unexpected error happened.
Please re-try.
Unexpected error happened.
Please re-try.
An internal system error occurred.
Repeat the AUTO SETUP procedure.
—