Yamaha DTXPRESS Manual Do Utilizador
53
1-5. Hi-Hat Offset
This sets the value of the data sent by a foot controller connected
to the HI HAT CONTROL jack on the rear panel. Set a + (plus) or
– (minus) level.
to the HI HAT CONTROL jack on the rear panel. Set a + (plus) or
– (minus) level.
UT
SYSTEM
HH
OffS=
0T=
32
q HH OFFS (Hi-Hat Offset)
When a low data value is received from the foot controller, the voice
will sound sooner. So, slightly pressing the foot controller will re-
sult in the voice sounding. In the case of the hi-hat controller, deli-
cate adjustment of the controller’s “closed” point is possible.
When a low data value is received from the foot controller, the voice
will sound sooner. So, slightly pressing the foot controller will re-
sult in the voice sounding. In the case of the hi-hat controller, deli-
cate adjustment of the controller’s “closed” point is possible.
w T (Foot Splash Detect Time)
Sets the detect time for the foot splash. Large values make foot
splashes easier to produce.
Sets the detect time for the foot splash. Large values make foot
splashes easier to produce.
* Values too large will result in splashes being produced under
normal hi-hat use.
q
w
1-6. Factory Set
This function replaces all internal settings in the DTXPRESS to
their factory-set condition.
their factory-set condition.
UT
SYSTEM
Factory
Set
The Factory Set function will replace all internal set-
tings in the DTXPRESS to their factory-set condi-
tion. Take care so as not to loose important data.
Make sure any settings and user songs you want to
keep have been saved to an external device such as
the Yamaha MIDI Data Filer MDF3, etc. (m[2-1.
Bulk Dump] (P. 53)
tings in the DTXPRESS to their factory-set condi-
tion. Take care so as not to loose important data.
Make sure any settings and user songs you want to
keep have been saved to an external device such as
the Yamaha MIDI Data Filer MDF3, etc. (m[2-1.
Bulk Dump] (P. 53)
Procedure
1. Enter the display shown above, press the [SAVE/ENT]
button. The following display will appear asking for con-
firmation before the Factory Set operation is carried out.
firmation before the Factory Set operation is carried out.
2. Once again, press the [SAVE/ENT] button to proceed
with the operation.
All
data
will
be
lost.AreYouSure?
2. MIDI Group
This sub-mode contains functions and settings for the MIDI and
TO HOST jacks of the DTXPRESS. This group is divided into the
following 10 pages.
TO HOST jacks of the DTXPRESS. This group is divided into the
following 10 pages.
2-1. Bulk Dump ....................................................... 53
2-2. Channel 10 Program Change/
2-2. Channel 10 Program Change/
Channel Event Receive ................................... 54
2-3. Receive Program Change/
System Exclusive Messages ........................... 54
2-4. Program Change Table .................................... 55
2-5. MIDI Mode ....................................................... 55
2-6. Device Number, Local Control ......................... 55
2-7. MIDI Merge ...................................................... 55
2-8. Dump Interval .................................................. 56
2-9. Send Hi-Hat Control ........................................ 56
2-10. Host Thru Port ................................................. 56
2-5. MIDI Mode ....................................................... 55
2-6. Device Number, Local Control ......................... 55
2-7. MIDI Merge ...................................................... 55
2-8. Dump Interval .................................................. 56
2-9. Send Hi-Hat Control ........................................ 56
2-10. Host Thru Port ................................................. 56
* Please refer to the [MIDI Data Format] (P. 80) section for more
information related to MIDI.
2-1. Bulk Dump
With the Bulk Dump operation, data stored in the ETXPRESS can
be transmitted via the MIDI OUT or TO HOST jack.
be transmitted via the MIDI OUT or TO HOST jack.
Utility Mode
q Fmt (Bulk Dump Format)
Selects the type of data to be transmitted with the Bulk Dump
operation.
Selects the type of data to be transmitted with the Bulk Dump
operation.
all
data
: All the data in the DTXPRESS
system
data : Data set in the Utility mode (except User
Map).
user
map
: User Map data.
one
drumkit : Data for the currently selected Drum Kit.
all
drumkit : All User Drum Kit Data.
one
trigger : Data for the currently selected Trigger Setup.
all
trigger : All User Trigger Setup data
one
song
: Data for the currently selected User Song.
all
song
: All User Song data.
Procedure
1. After reading the [Connecting a MIDI Device] (P. 12) or
the [Connecting a Computer] (P. 26) section, connect the
external MIDI device or computer to the MIDI OUT or TO
HOST jack on the DTXPRESS. Set the HOST SELECT
switch.
external MIDI device or computer to the MIDI OUT or TO
HOST jack on the DTXPRESS. Set the HOST SELECT
switch.
UT
MIDI
BULKDUMP
Fmt=
all
data
q