Yamaha DTXPRESS Manual Do Utilizador
54
Utility Mode
2. Select the type of bulk data (that will be sent) in the dis-
play shown above and press the [SAVE/ENT] button.
The display shown below will appear.
The display shown below will appear.
2-2. Channel 10 Program Change/Channel Event Receive
This enables or disables the DTXPRESS to receive program change
messages/channel events through MIDI channel 10. Program
change messages received or transmitted through channel 10 can
be used to switch DTXPRESS drum kits.
It is necessary to set the receive parameter to “on” in this display
in order to switch the DTXPRESS’ drum kits from a song or an
external MIDI device.
messages/channel events through MIDI channel 10. Program
change messages received or transmitted through channel 10 can
be used to switch DTXPRESS drum kits.
It is necessary to set the receive parameter to “on” in this display
in order to switch the DTXPRESS’ drum kits from a song or an
external MIDI device.
3. Press the [SAVE/ENT] or [VALUE+] button, the bulk dump
will be carried out.
* Press [VALUE-] to cancel the bulk dump.
When the operation is complete, the LCD will display “Com-
plete
” as shown below.
BULK
all
data
Are
you
sure
?
* The device number must be set for bulk dumps [2-6. Device
Number, Local Control] (P. 55)
* Refer to the [MIDI Data Format] section (P. 80) for more infor-
mation on bulk dump operations.
BULK sssssssssss
Complete
!
Receiving Bulk Data
DTXPRESS data stored in an external device can be sent back
to the DTXPRESS’ MIDI IN/TO HOST jack using Bulk Data
Receive.
to the DTXPRESS’ MIDI IN/TO HOST jack using Bulk Data
Receive.
1. After reading the [Connecting a MIDI Device] (P. 12)
or the [Connecting a Computer] (P. 26) section, con-
nect the MIDI device or computer to the MIDI OUT
jack/TO HOST jack on the DTXPRESS. Set the
HOST SELECT switch.
nect the MIDI device or computer to the MIDI OUT
jack/TO HOST jack on the DTXPRESS. Set the
HOST SELECT switch.
2. With the sequencer (song, metronome) stopped,
send bulk data from the external device.
3. When the DTXPRESS starts receiving data, the fol-
lowing screen will appear on the LCD.
4. When the DTXPRESS has completed receiving all
the data, the following screen will appear on the LCD
for a few seconds, then the screen will return to the
original display (before receiving bulk data).
for a few seconds, then the screen will return to the
original display (before receiving bulk data).
* Before receiving bulk data, it is necessary to match the de-
vice numbers (P. 55 [2-6]) of the DTXPRESS and the exter-
nal device. It is also necessary to enable the DTXPRESS
to receive exclusive messages (P. 54 [2-3]).
nal device. It is also necessary to enable the DTXPRESS
to receive exclusive messages (P. 54 [2-3]).
BULK
Receiving
Please
wait...
BULK Receiving
BULK
Received.
q 10PC (Receive Program Change)
This enables or disables the DTXPRESS to receive program change
messages through MIDI channel 10.
off: Does not receive.
on: Receives.
This enables or disables the DTXPRESS to receive program change
messages through MIDI channel 10.
off: Does not receive.
on: Receives.
* Even if the q 10PC parameter is set to “on”, program change
messages from MIDI channel 10 will not be received in the fol-
lowing cases.
• If the w 10 (receive channel event) parameter is set to “off”
• If the [2-3. Receive Program Change/System Exclusive
lowing cases.
• If the w 10 (receive channel event) parameter is set to “off”
• If the [2-3. Receive Program Change/System Exclusive
Message’s] q PC (program change) parameter is set to “off”.
w 10 (Receive Channel Event)
This enables or disables the DTXPRESS to receive MIDI channel
messages through MIDI channel 10.
off: Does not receive.
on: Receives.
This enables or disables the DTXPRESS to receive MIDI channel
messages through MIDI channel 10.
off: Does not receive.
on: Receives.
2-3. Receive Program Change/System
Exclusive Messages
This enables or disables the DTXPRESS to receive program change
messages/system exclusive messages from all MIDI channels.
messages/system exclusive messages from all MIDI channels.
q PC (Receive Program Change)
off: Does not receive program change messages.
on: Receives program change messages.
off: Does not receive program change messages.
on: Receives program change messages.
w SySex (Receive System Exclusive Messages)
off: Does not receive system exclusive messages.
on: Receives system exclusive messages.
off: Does not receive system exclusive messages.
on: Receives system exclusive messages.
UT
MIDI
RECEIVE
10PC=
on
10=
on
q
w
UT
MIDI
RECEIVE
PC=
on
SySEx=
on
q
w