DeLonghi ESAM04.350 Manual Do Utilizador

10

11

during rinsing, a little hot water comes out of the coffee spouts 
and is collected in the drip tray underneath. avoid contact with 
splashes of water.
•  To turn the appliance on, press the

button (fig. 5). 

The message “heating up Please wait” is displayed.

after heating, the message “rinsing” is displayed, together with 
a progress bar which gradually fills as preparation progresses. 
as  well  as  heating  the  boiler,  the  appliance  also  heats  the 
internal circuits by circulating hot water. 
The appliance is at temperature when the message indicating 
the taste and quantity of coffee appears. 

each time the appliance is turned off, it performs an automatic 
rinse cycle which cannot be interrupted.

To  avoid  damaging  the  appliance,  always  press  the 
button to turn off.

during rinsing, a little hot water flows from the coffee spouts 
(only if coffee has been made).  
avoid contact with splashes of water. 
To turn the appliance off, press the button

(fig. 5). The 

appliance performs a rinse cycle then goes off.

if the appliance is not used for an extended period, place the 
main switch in the 0 position (fig. 6).
never  place  the  main  switch  in  the  0  position  while  the 
appliance is on.
no rinse is performed if no drinks with coffee have been made 
while the machine has been on. 

When you access the settings menu by pressing the MENU button, the 

following menu items can be selected:  descale,  Set language, energy 

saving,  adjust  time,  auto-start,  auto-off,  Set  temperature,  Water 
hardness, Statistics, default values.

Descaling
For instructions on descaling, see page 16. 

Setting the language 
To modify the language of the display, proceed as follows:
1.   Press the MENU button to enter the settings menu.
2.   Press the  or  button until “Set language” is displayed;
3.   Press the OK button;

4.   Press  the  or button  until  the  required  language  is 

displayed;

5.   Press the OK button to confirm;
6.   Press the ESC button exit the menu.

Energy Saving
use this function to enable or disable “energy saving” mode. 
When enabled, the function reduces energy consumption in 
compliance with european regulations.  
To enable or disable the function, proceed as follows:
1.  Press the MENU button to enter the settings menu.
2.  Press the  or  button until “energy saving” is displayed;
3.   Press the OK button. “disable?” is displayed (or “enable?” 

if the function has already been disabled). 

4.  Press the OK button to disable or enable the function or 

the ESC button to exit the menu.

When  the  function  is  active,  if  the  machine  is  not  used  for 
about 1 minute, “energy saving” is displayed.

•  To exit “Energy saving” mode, press any button, then press

the button corresponding to the drink you want to make. 

•  A few seconds may elapse between “Energy saving” mode

and delivery of the first drink; “Preparation underway...” is 
displayed. 

To adjust the time on the display, proceed as follows:

1.   Press the MENU button to enter the settings menu.
2.   Press the   or  button until “adjust time” is displayed;

3.   Press the OK button. The hours flash on the display;
4.   Press the   or button to change the hours;

5.   Press the OK button to confirm. The minutes flash on the 

display;

6.   Press the   or button to change the minutes;

7.   Press the OK button to confirm;

8.   Press the ESC button to exit the settings menu.

The  time  is  displayed  when  the  appliance  is  in  stand-by  or 
energy saving mode. if the time has not been adjusted, “0:00” 
flashes on the display.

Auto-Start
you can set the auto-start time in order to have the appliance 
ready at a certain time (for example in the morning) so you can 
make coffee immediately. 

To enable this function, the time must be set correctly.

To enabled auto-on, proceed as follows:

1.   Press the MENU button to enter the settings menu.
2.   Press the  or button until “auto-start” is displayed;
3.   Press the OK button. “enable?” is displayed;
4.  Press the OK button. The hours flash on the display;
5.  Press the   or button to select the hours;
6.   Press the OK button to confirm. The minutes flash on the 

display;

7.   Press the  or button to change the minutes;
8.   Press the OK button to confirm. The  

 symbol appears 

under “auto-start” on the display.

9.   Press the eSC button to exit the menu. When the appliance 

is in stand-by, the  

symbol appears next to the clock 

to indicate that auto-start has been programmed.

To disable the function:
1.   Press the MENU button to enter the settings menu.
2.   Press the  or button until “auto-start” is displayed;
3.  Press the OK button. “disable?” is displayed;
4.  Press the OK button to confirm;
5.  Press the ESC button to exit the menu. When the appliance 

is in stand-by, the  

 symbol is no longer displayed. 

Auto-Off (Stand-by)
The appliance is set by default to go off if not used for two 
hours.  
The time can be changed so that the appliance switches off 
after 15 or 30 minutes, or after 1, 2 or 3 hours.  
To re-programme auto-off, proceed as follows:
1.   Press the MENU button to enter the settings menu.
2.  Press the  or  button until “auto-off” is displayed;
3.   Press the OK button;
4.  Press the   or  button until the required time (15 or 30 

minutes, or 1, 2 or 3 hours) is displayed;

5.  Press the OK button to confirm;
6.  Press the ESC button exit the menu.
auto-off is programmed. 

Setting the temperature
To  modify  the  temperature  of  the  water  used  to  make  the 
coffee, proceed as follows:
1.   Press the MENU button to enter the settings menu.
2.  Press  the  or button  until  “Set  temperature”  is 

displayed;

3.  Press the OK button;
4.   Press the  or button until the required temperature is 

displayed (l = low; llll = high);

5.   Press the OK button to confirm;
6.   Press the ESC button exit the menu.
Setting water hardness
For instructions on setting water hardness, see page 17.