DeLonghi 5713214281 Manual Do Utilizador

9

after  removing  the  packaging,  make  sure  the  product  is 

complete and undamaged and that all accessories are present.

do  not  use  the  appliance  if  it  is  visibly  damaged.  Contact 
de’longhi Customer Services. 

When  you  install  the  appliance,  you  should  respect  the 

following safety warnings:

•  The  appliance  gives  off  heat.  After  positioning  the

appliance on the worktop, leave a space of at least 3 cm 

between the surfaces of the appliance and the side and 

rear walls and at least 15 cm above the coffee maker.

•  Water penetrating the appliance could cause damage. Do

not place the appliance near taps or sinks. 

•  The appliance could be damaged if the water it contains

freezes. do not install the appliance in a room where the 

temperature could drop below freezing point. 

•  Arrange the power cable in such a way that it cannot be

damaged  by  sharp  edges  or  contact  with  hot  surfaces 

(e.g. electric hot plates).

Check  that  the  mains  power  supply  voltage  corresponds  to 
the value indicated on the rating plate on the bottom of the 
appliance.

Connect the appliance to an efficiently earthed and correctly
installed socket with a minimum current rating of 10a only.
if the power socket does not match the plug on the appliance, 
have the socket replaced with a suitable type by a qualified 
professional.

•  Coffee has been used to factory test the appliance and it is

therefore completely normal for there to be traces of coffee 
in the grinder.  The machine is, however, guaranteed to be 
new. 

•  You should customise water hardness as soon as possible

following the instructions in the section “Setting water 
hardness” on page 16.

1.  Plug the appliance into the mains socket and place the 

main switch on the back of the appliance in the i position 
(fig. 1).

you  must  first  choose  the  language  (the  languages  scroll 
through at intervals of about 3 seconds).
2.  When “english” appears, press the OK button (fig. 2) for a 

few seconds until “eNgliSh set” is displayed. 

Follow the instructions indicated by the appliance:
3.  “FILL TANK”: remove the water tank, fill to the MAX line

with fresh water then replace in the appliance (fig. 3). 

4.   Turn the cappuccino maker outwards and place a container 

with a minimum capacity of 100 ml underneath (fig. 4).

5.  “TURN STEAM KNOB” is displayed. When the steam knob

is turned to the I position (fig. 4), “Hot water Press OK” is
displayed. 

6.   Press the OK button (fig. 2). 
 

“Please  wait”  is  displayed  and  the  appliance  begins  to 
deliver water from the hot water spout.

The  appliance  ends  the  first  start  up  procedure,  then  the 
message  “Turning  off,  Please  wait”  is  displayed  and  the 
appliance goes off.
The coffee maker is now ready for normal use. 

•  When using the appliance for the first time, you need to

make  4-5  cups  of  coffee  or  4-5  cappuccinos  before  the 
appliance starts to give satisfactory re-sults.

Before turning the appliance on, make sure the main switch on 
the back of the appliance is in the i position (fig. 1).
each time the appliance is turned on, it performs an automatic 
preheat and rinse cycle which cannot be interrupted. 
The  appliance  is  ready  for  use  only  after  completion  of  this 
cycle. 

during rinsing, a little hot water comes out of the coffee spouts 
and is collected in the drip tray underneath.
avoid contact with splashes of water. 
•  To turn the appliance on, press the

button (fig. 5). 

The message “heating up, Please wait” is displayed.

after heating, the message “rinsing” is displayed. as well as 
heating the boiler, the appliance also heats the internal circuits 
by circulating hot water. 
The appliance is at temperature when the message indicating 
the taste and quantity of coffee appears. 

each time the appliance is turned off, it performs an automatic 
rinse cycle which cannot be interrupted.