Yamaha HTR-5790 Manual Do Utilizador
60
REMOTE CONTROL FEATURES
You can control other components by setting the
appropriate manufacturer codes. Codes can be set up for
each input area.
appropriate manufacturer codes. Codes can be set up for
each input area.
The following table shows the factory preset component
(Library: component category) and the manufacturer code
for each area.
(Library: component category) and the manufacturer code
for each area.
You may not be able to operate your YAMAHA component even
if a YAMAHA manufacturer code is initially set as listed above.
In this case, try to set other YAMAHA manufacturer code(s).
if a YAMAHA manufacturer code is initially set as listed above.
In this case, try to set other YAMAHA manufacturer code(s).
1
Press an input selector button to select the
source component you want to set up.
source component you want to set up.
2
Press and hold LEARN for about 3 seconds
using a ballpoint pen or similar object.
using a ballpoint pen or similar object.
“SETUP” and the selected component name appear
alternately in the display window.
alternately in the display window.
Be sure to press and hold LEARN for at least 3
seconds, otherwise the learning process will start.
seconds, otherwise the learning process will start.
y
Complete each of the following steps in 30 seconds.
Otherwise, the learning mode will be automatically
canceled. In this case, press LEARN again.
Otherwise, the learning mode will be automatically
canceled. In this case, press LEARN again.
If you want to change a library (component
category), press
category), press
j
/
i
. You can set a different
type of component.
Library choices: L:DVD, L:LD, L:CD, L:CDR,
L:MD, L:TAP (tape), L:TUN, L:AMP*, L:TV,
L:CAB (cable), L:DBS, L:SAT, L:VCR
L:MD, L:TAP (tape), L:TUN, L:AMP*, L:TV,
L:CAB (cable), L:DBS, L:SAT, L:VCR
* The amplifier Library (L:AMP) code is preset to “YPC”
to operate this unit. However, you can switch between the
following two codes if necessary.
following two codes if necessary.
• The initial setting for “Amplifier library” is “YPC”.
YPC
To operate this unit.
ZONE
(U.S.A., Canada and Australia models only)
To operate ZONE 2 or ZONE 3 features.
To operate ZONE 2 or ZONE 3 features.
3
Press
u
/
d
to select the name of your
component’s manufacturer.
You will find the names of most worldwide audio-
video manufacturers in alphabetical order in the
display window.
video manufacturers in alphabetical order in the
display window.
4
Press one of the buttons shaded below to
see if you can control your component. If you
can, the manufacturer code is correct.
see if you can control your component. If you
can, the manufacturer code is correct.
y
• If the manufacturer of your component has more than one
codes, try each of them until you find the correct one.
• If you continuously want to set up another code for
another component, press TV MUTE/SELECT and repeat
steps 1, 3 and 4.
steps 1, 3 and 4.
Setting manufacturer codes
Input area
Component
category
(Library)
(Library)
Manufacturer
PHONO
TV –
TUNER
TUNER
YAMAHA-1
CD
CD
YAMAHA-1
V-AUX
VCR –
CBL/SAT
CABLE
–
MD/TAPE
MD
YAMAHA-1
CD-R
CD-R
YAMAHA
DTV
TV
–
VCR 1
VCR
–
DVR/VCR2
VCR
–
DVD
DVD
YAMAHA-1
Note
TUNER
PHONO
V-AUX
DTV
DVR/VCR2
VCR 1
DVD
CBL/SAT
MD/TAPE
CD-R
CD
MULTI CH IN
LEARN
TV VOL
PRESET
PRESET
TV MUTE
TV VOL
SELECT
CH
CH
+
+
–
–
POWER
REC
DISC SKIP
SET MENU
TV INPUT
A/B/C/D/E
AUDIO
VOL
LEVEL
MENU
TV VOL
TITLE
MUTE
POWER
AMP
AV
TV
+
+
–
00_HTR-5790U_EN.book Page 60 Tuesday, December 9, 2003 9:16 AM