Yamaha HTR-5790 Manual Do Utilizador
62
REMOTE CONTROL FEATURES
5
Press and hold the button you want to
program on the other remote control until
“OK” appears in the display window.
program on the other remote control until
“OK” appears in the display window.
• “NG” appears in the display window if programming was
unsuccessful. In this case, start over from step 5.
• This remote control can learn approximately 120 functions.
However depending on the signals learned, “FULL” may
appear in the display before you program 120 functions. In this
case, clear unnecessary programmed functions to make room
for further learning.
appear in the display before you program 120 functions. In this
case, clear unnecessary programmed functions to make room
for further learning.
6
Repeat steps 4 and 5 to program additional
functions.
functions.
7
Press LEARN again to exit from the learning
mode.
mode.
• Learning may not be possible in the following cases:
– When the batteries in the remote control for this unit or other
components are weak.
– When the distance between the two remote controls is too
great or too small.
– When the remote control infrared windows are not facing at
the appropriate angle.
– When the remote control is exposed to direct sunlight.
– When the function to be programmed is continuous or
– When the function to be programmed is continuous or
uncommon.
• “ERROR” appears in the display window if you press more
than one button at the same time.
You can change the name that appears in the display
window on the remote control if you want to use the
different name than the factory preset. This is useful when
you have set the input selector to control a different
component.
window on the remote control if you want to use the
different name than the factory preset. This is useful when
you have set the input selector to control a different
component.
1
Press an input selector button
to select the
source component you want to rename.
The selected component name appears in the display
window.
window.
2
Press RE-NAME using a
ballpoint pen or similar
object.
ballpoint pen or similar
object.
3
Press
u
/
d
to select and enter a character.
Pressing d changes the character as follows:
A to Z, a to z, 0 to 9, space, -(hyphen), and /(slash).
(Pressing u changes the characters in reverse order.)
A to Z, a to z, 0 to 9, space, -(hyphen), and /(slash).
(Pressing u changes the characters in reverse order.)
4
Press
j
/
i
to move the cursor to the next
position.
y
If you want to continue setting up names for other
components, press TV MUTE/SELECT and repeat steps 1,
3 and 4.
components, press TV MUTE/SELECT and repeat steps 1,
3 and 4.
5
Press RE-NAME again to exit from the
renaming mode.
renaming mode.
Notes
Notes
PHONO
PO
WER
SLEEP
CLEAR
LEARN
ST
ANDBY
TRANSMIT
RE–NAME
INPUT MODE
SYSTEM
V
-AU
X
X
DTV
PO
WER
PO
WER
AMP
AV
TV
D
V
R/VCR2
VCR 1
D
VD
SELECT
CBL/SA
T
MD/T
APE
CD-R
TUNER
MUL
TI CH IN
CD
LEARN
Changing source names in the
display window
display window
TUNER
PHONO
V-AUX
DTV
DVR/VCR2
VCR 1
DVD
CBL/SAT
MD/TAPE
CD-R
CD
MULTI CH IN
RE-NAME
TV VOL
PRESET
PRESET
TV MUTE
TV VOL
SELECT
CH
CH
+
+
–
–
TV VOL
PRESET
PRESET
TV MUTE
TV VOL
SELECT
CH
CH
+
+
–
–
RE-NAME
00_HTR-5790U_EN.book Page 62 Tuesday, December 9, 2003 9:16 AM