Kurzweil k2600 Guia De Configuração Rápida
2-2
Startup
Startup—the Details
just to the right of the display; theyÕre labeled with
Up
/
Down
/
Left
/
Right
arrows). Press
one of the cursor buttons, and the cursor moves correspondingly. In our example below,
the BasicChannel parameter is selected; its value is
the BasicChannel parameter is selected; its value is
1
.
4. Select the LocalKbdCh parameter (that stands for Local Keyboard Channel), then use the
dial (we call it the Alpha Wheel) to change the value so that it matches the channel that
your controller is sending on.
your controller is sending on.
MIDIMode:RECEIVE||||||||||||||||||||||||
BasicChannel:
1||||||||
|SysExID:|||0|||||
MIDI|Mode|||:Multi|||||SCSI|ID:|||6|||||
AllNotesOff|:Normal||||BendSmooth:On||||
ProgChgType|:Extended||LocalKbdCh:None||
VelocityMap:|1|Linear||BankSelect:Ctl|32
AllNotesOff|:Normal||||BendSmooth:On||||
ProgChgType|:Extended||LocalKbdCh:None||
VelocityMap:|1|Linear||BankSelect:Ctl|32
Pressu
r
eMap:|
1
|Linea
r
||Powe
r
Mode|:
U
ser||
XMIT||
|
RECV||
|
CHANLS
|
PrgChg
|
RsetCh
|
Panic
5. Press the button labeled
Exit
to get out of MIDI mode. YouÕre ready to go. See page 10-7
for more information about the local keyboard channel.
Start Jamming!
1. Power up your K2600 and check out some of the programs and setups. The K2600 starts
up in either Program mode or Setup modeÑwhichever of the two modes it was in when it
was last shut down (or given a soft reset). Press the button labeled
was last shut down (or given a soft reset). Press the button labeled
Program
or
Setup
to
switch modes.
2. If you hear distortion, reduce the gain on your mixing board, or use the pad if it has one.
3. Scroll through the program list with the Alpha Wheel.
4. Press the
Quick Access
mode button and use the alphanumeric buttons to select from
programmable banks of ten programs or setups.
5. If you donÕt hear anything, review these steps, or check the Troubleshooting section in the
.
Startup—the Details
This section walks you through the hookup of your K2600. WeÕll take a look at the rear panel,
then describe the power, audio, and other cable connections.
then describe the power, audio, and other cable connections.
Before You Start...
DonÕt connect anything until you make sure your K2600 is properly and safely situated. Also, if
your K2600 has been out in the cold, give it time to warm up to room temperature before
starting it, since condensation may have formed inside the K2600.
your K2600 has been out in the cold, give it time to warm up to room temperature before
starting it, since condensation may have formed inside the K2600.
YouÕll probably be mounting a K2600R in a standard 19-inch MIDI rack (it takes up three rack
spaces). If you will be transporting the rack containing the K2600R, be sure to support the back
of the K2600R within the rack. If youÕre not installing the K2600R in a rack, it should rest on a
hard ßat surface. In this case, it
spaces). If you will be transporting the rack containing the K2600R, be sure to support the back
of the K2600R within the rack. If youÕre not installing the K2600R in a rack, it should rest on a
hard ßat surface. In this case, it
must
rest on its rubber feet (supplied in the packing carton), and
not
on the bottom panel.