Adtran 3458-poe Guia De Configuração Rápida
2
Copyright © 2009 ADTRAN, Inc. All Rights Reserved.
Quick Start Guide, 61200824G1-13A, March 2009
3
C
ONFIGURE
THE
U
NIT
’
S
IP A
DDRESS
The following steps create an IP address and subnet mask for ETH 0/1. If you are not sure what
IP address to assign, please contact your network administrator.
IP address to assign, please contact your network administrator.
1.
At the # prompt, enter config terminal.
2.
At the (config)# prompt, enter interface eth 0/1 to access the configuration parameters for
the Ethernet port located on the rear of the unit.
the Ethernet port located on the rear of the unit.
3.
Enter ip address 10.26.12.12 255.255.255.0 to assign an IP address to the Ethernet port
using a 24-bit subnet mask.
using a 24-bit subnet mask.
4.
Enter ip route 0.0.0.0 0.0.0.0 192.22.72.2 to add a default route to the route table. If
necessary, contact your network administrator to obtain the IP address (and subnet mask)
for your particular configuration.
necessary, contact your network administrator to obtain the IP address (and subnet mask)
for your particular configuration.
5.
Enter no shutdown to activate the interface to pass data.
6.
Enter exit to exit the Ethernet interface commands and return to the Global Configuration
mode.
mode.
E
NABLE
T
ELNET
A
CCESS
The following steps create a password of adtran for Telnet access. By default, Telnet access is
enabled with a password of password.
enabled with a password of password.
1.
Verify that the prompt of your unit displays (config)#.
2.
Enter line telnet 0 4 to change the configuration parameters for the Telnet sessions.
3.
Enter login to initiate Telnet access.
4.
Enter password adtran to change the login password for the Telnet sessions.
5.
Enter exit to return to the Global Configuration mode.
6.
Verify that the prompt of your unit displays (config)#.
7.
Enter do write memory to save the current configuration.
The configuration parameters used in the examples outlined in this
document are for instructional purposes only. Please replace all
underlined entries (
document are for instructional purposes only. Please replace all
underlined entries (
example
) with your specific parameters to configure
your application.
Depending on your configuration, you may need to set a default gateway
as well using the (config)#ip default gateway command. If IP routing is
enabled on the unit, do NOT set a default gateway.
as well using the (config)#ip default gateway command. If IP routing is
enabled on the unit, do NOT set a default gateway.
C
ONSOLE
P
INOUTS
Pin
Name
Description
1
DCD
Data Carrier Detect (output)
2
RD
Receive Data (output)
3
TD
Transmit Data (input)
4
DTR
Data Terminal Ready (input)
5
SG
Signal Ground
6
—
Tied to Pin 1 (output)
7
—
Unused
8
—
Tied to Pin 1 (output)
9
—
Unused
E
THERNET
P
INOUTS
Pin
Name
Description
1
TX1
Transmit Positive
2
TX2
Transmit Negative
3
RX1
Receive Positive
4, 5
—
Unused
6
RX2
Receive Negative
7, 8
—
Unused
S
WITCH
P
ORT
(1
THROUGH
8) P
INOUTS
Pin
Name
Description
1
TX1
Transmit Positive (PoE negative rail)
2
TX2
Transmit Negative (PoE negative rail)
3
RX1
Receive Positive (PoE positive rail)
4, 5
—
Unused
6
RX2
Receive Negative (PoE positive rail)
7, 8
—
Unused