Power Acoustik bamf-1200 Guia Do Utilizador
- 8 -
CONTROL FUNCTIONS
1. RCA input jacks
These RCA input jacks are for use with source units that have RCA or Line level
outputs. A source unit with a minimum level of 200mV is required for proper operation.
The use of high quality twisted pair cables is recommended to decrease the possibility
of radiated noise entering the system.
These RCA input jacks are for use with source units that have RCA or Line level
outputs. A source unit with a minimum level of 200mV is required for proper operation.
The use of high quality twisted pair cables is recommended to decrease the possibility
of radiated noise entering the system.
2. GAIN Control
The level control will match the amplifiers sensitivity to the source units signal voltage.
The Operating range is 200mV minimum to 6V maximum.
The level control will match the amplifiers sensitivity to the source units signal voltage.
The Operating range is 200mV minimum to 6V maximum.
CAUTION: Do not run the amplifier in high volume for long time, otherwise the loudspeakers will be
damaged.
damaged.
3. Full pass x-over switch
When the switch is in the "Full" position, the full range is bypassed.
When the switch is in the "Full" position, the full range is bypassed.
4. Low pass x-over switch
When the switch is in the "LPF" position, frequencies lower than the low pass frequency
setting are passed.
When the switch is in the "LPF" position, frequencies lower than the low pass frequency
setting are passed.
4.1 Low pass x-over frequency control
This control is used to select the desired low pass x-over frequency.
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The frequency can be
adjusted between 30Hz and 250Hz.
BAMF2000/1D, 4000/1D, 55001D : The frequency can be adjusted between 40Hz and
200Hz.
This control is used to select the desired low pass x-over frequency.
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The frequency can be
adjusted between 30Hz and 250Hz.
BAMF2000/1D, 4000/1D, 55001D : The frequency can be adjusted between 40Hz and
200Hz.
5. High pass x-over switch
When the switch is in the "HPF" position, frequencies higher than the high pass
frequency setting are passed.
When the switch is in the "HPF" position, frequencies higher than the high pass
frequency setting are passed.
5.1 High pass x-over frequency control
This control is used to select the desired high pass x-over frequency.
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The frequency can be
adjusted between 50Hz and 500Hz.
This control is used to select the desired high pass x-over frequency.
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The frequency can be
adjusted between 50Hz and 500Hz.
6.Bass EQ
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The boost can be
adjusted between 0dB to12dB.
BAMF2000/1D, 4000/1D, 55001D : The boost can be adjusted between 0dB to 18dB.
BAMF800/2, 1250/2, 1800/2, 2200/2, 2600/2, 1200/4, 1600/4 : The boost can be
adjusted between 0dB to12dB.
BAMF2000/1D, 4000/1D, 55001D : The boost can be adjusted between 0dB to 18dB.
7. Auxiliary outputs
The Auxiliary outputs offer Power Acoustik amplifiers easy, unlimited system expansion.
Route RCA's from the line out of the first amplifier to the line input of a second
amplifier when using a single source output.
The Auxiliary outputs offer Power Acoustik amplifiers easy, unlimited system expansion.
Route RCA's from the line out of the first amplifier to the line input of a second
amplifier when using a single source output.