Power Acoustik bamf-1200 Guia Do Utilizador
- 9 -
CONTROL FUNCTIONS
8. SUBSONIC
BAMF1250/2, 1800/2, 22200/2, 2600/2 : The frequency can be adjusted between 15Hz
and 50Hz.
BAMF2000/1D, 4000/1D, 5500/1D : The frequency can be adjusted between 20Hz and
50Hz.
BAMF1250/2, 1800/2, 22200/2, 2600/2 : The frequency can be adjusted between 15Hz
and 50Hz.
BAMF2000/1D, 4000/1D, 5500/1D : The frequency can be adjusted between 20Hz and
50Hz.
9. REMOTE
Controls the subwoofer amplifier gain, from a remote location for ease of adjustment
during listening.
Controls the subwoofer amplifier gain, from a remote location for ease of adjustment
during listening.
Warning: Do not connect a level control knob from other manufacturers to the Remote Sub Level
Control of any amplifier. Even though the connectors fit properly, the control knob and connector
pin positions may be different and the amplifier will be damaged.
Control of any amplifier. Even though the connectors fit properly, the control knob and connector
pin positions may be different and the amplifier will be damaged.
10. PHASE
0°or180° selectable for switching the phase of the output to the woofer.
0°or180° selectable for switching the phase of the output to the woofer.
11. MASTER/SLAVE MODE[BAMF2000/1D, 4000/1D, 5500/1D]
Controls whether the amplifier is a slave or master when connected in combined
amplifier configurations. (Refer to the Master Mode section of this guide.)
All of the controls will be adjusted by the "Master" amplifier.
-Slave mode : To be switched " Slave mode" when linking one amplifier with another
amplifier.
-Master mode : To be switched " Master mode" when only using this single amplifier.
Controls whether the amplifier is a slave or master when connected in combined
amplifier configurations. (Refer to the Master Mode section of this guide.)
All of the controls will be adjusted by the "Master" amplifier.
-Slave mode : To be switched " Slave mode" when linking one amplifier with another
amplifier.
-Master mode : To be switched " Master mode" when only using this single amplifier.
12. INPUT MODE
Selects 2, 3 or 4 channel operation(FIG. 1)
Selects 2, 3 or 4 channel operation(FIG. 1)
13. GND
Connect this terminal directly to the sheet metal chassis of the vehicle, using the
shortest wire necessary to make this connection. Always use wire of the same gauge
or larger than the (+)12 volt power wire. The chassis connection point should be
scraped free of paint and dirt. Use only quality crimped and/or soldered connectors
at both ends of this wire.
Connect this terminal directly to the sheet metal chassis of the vehicle, using the
shortest wire necessary to make this connection. Always use wire of the same gauge
or larger than the (+)12 volt power wire. The chassis connection point should be
scraped free of paint and dirt. Use only quality crimped and/or soldered connectors
at both ends of this wire.
Warning : Do not connect this terminal directly to the vehicle battery ground terminal or any other
factory ground points.
factory ground points.
14. Remote Turn On
This terminal turns on the amplifier when (+)12 volt is applied to it. Connect it to the
remote turn on lead of the head unit or signal source.
This terminal turns on the amplifier when (+)12 volt is applied to it. Connect it to the
remote turn on lead of the head unit or signal source.
15. (+)12 Volt Power
Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of
the vehicle battery or the positive terminal of an isolated audio system battery.
Connect this terminal through a FUSE or CIRCUIT BREAKER to the positive terminal of
the vehicle battery or the positive terminal of an isolated audio system battery.
Warning: Always protect this power wire by installing a fuse or circuit breaker of the appropriate
size within 12 inches of the battery terminal connection.
size within 12 inches of the battery terminal connection.