Kent Euroclean 152 Guia Do Utilizador
7 - FORM NO. 56041490 / DuraVac
™
152
A-KNOW YOUR MACHINE
As you read this manual, you will occasionally run across a bold number
in parentheses - example: (2). These numbers refer to an item shown
on this page. Refer back to this page whenever necessary, to pinpoint
the location of an item mentioned in the text.
in parentheses - example: (2). These numbers refer to an item shown
on this page. Refer back to this page whenever necessary, to pinpoint
the location of an item mentioned in the text.
1
Handle
2
Cord Hook
3
Vacuum Hose
4
Handle Lock Button
5
Bag Housing
6
Carrying Handle
7
Red Light
8
Green Light
9
Brush Housing
10 Brush Height Adjustment Knob
11 Pedal
12 Power Cord
13 Wand
14 Crevice Tool
15 “Bag Full” Light
16 Bag Housing Latch
17 Main Power Switch
18 Exhaust Filter Cover
19 Filter Cover Latch
20 Power Cord Clamp (Figure B)
21 Locking Latch (Figure B)
22 Dusting Brush
11 Pedal
12 Power Cord
13 Wand
14 Crevice Tool
15 “Bag Full” Light
16 Bag Housing Latch
17 Main Power Switch
18 Exhaust Filter Cover
19 Filter Cover Latch
20 Power Cord Clamp (Figure B)
21 Locking Latch (Figure B)
22 Dusting Brush
B-SET UP AND ASSEMBLY
1
Carefully remove the machine from its carton.
2
Push the Handle (1) into the opening at the top of the Bag Housing
(5) until the button snaps into the hole between the Switch (17) and
the Bag Full Light (15).
(5) until the button snaps into the hole between the Switch (17) and
the Bag Full Light (15).
3
Install the Bag Housing (5) on the Brush Housing (9). Slide the
Locking Latch (21) to the left.
Locking Latch (21) to the left.
4
Measure 15 inches of Power Cord (12) from where it comes out of
the machine. Insert the cord at this point into the Power Cord Clamp
(20).
the machine. Insert the cord at this point into the Power Cord Clamp
(20).
5
Insert one end of the Vacuum Hose (3) into the top of the vacuum
body and the other end into the extension wand. Insert the wand
into the hole on the right side of the vacuum body and clip onto the
right side of the machine. Snap the Hose (3) into the clip below the
Handle (1).
body and the other end into the extension wand. Insert the wand
into the hole on the right side of the vacuum body and clip onto the
right side of the machine. Snap the Hose (3) into the clip below the
Handle (1).
6
To install a Paper Dust Bag, push the Bag Housing Latch (16) and
remove the back cover. Then follow the instructions printed on the
Paper Dust Bag. Never operate the machine without a Dust Bag
in place.
remove the back cover. Then follow the instructions printed on the
Paper Dust Bag. Never operate the machine without a Dust Bag
in place.
INTRODUCTION
This manual will help you get the most from your Kent DuraVac™. Read
it thoroughly before operating the machine.
it thoroughly before operating the machine.
Note: Bold numbers in parentheses indicate an item illustrated on
page 1.
page 1.
This product is intended for commercial use only.
PARTS AND SERVICE
Repairs, when required, should be performed by your Authorized Kent
Service Center, who employs factory trained service personnel, and
maintains an inventory of Kent original replacement parts and accesso-
ries.
Service Center, who employs factory trained service personnel, and
maintains an inventory of Kent original replacement parts and accesso-
ries.
Call the KENT DEALER named below for repair parts or service. Please
specify the Model and Serial Number when discussing your machine.
specify the Model and Serial Number when discussing your machine.
(Dealer, affix service sticker here.)
NAME PLATE
The Model Number and Serial Number of your machine are shown on the
Nameplate on the machine. This information is needed when ordering
repair parts for the machine. Use the space below to note the Model
Number and Serial Number of your machine for future reference.
Nameplate on the machine. This information is needed when ordering
repair parts for the machine. Use the space below to note the Model
Number and Serial Number of your machine for future reference.
MODEL NUMBER
SERIAL NUMBER
UNCRATE THE MACHINE
When the machine is delivered, carefully inspect the shipping carton and
the machine for damage. If damage is evident, save the shipping carton
so that it can be inspected. Contact the Kent Customer Service
Department immediately to file a freight damage claim.
the machine for damage. If damage is evident, save the shipping carton
so that it can be inspected. Contact the Kent Customer Service
Department immediately to file a freight damage claim.