Citel 6000 Guia Do Utilizador
PBXgateway
™
& EXTender
TM
6000 System Administrator’s Guide
102
ConneX Parameters
Table 1:
ConneX Port Parameters
Parameter Description
Enable
Enable
This will enable ConneX features on the selected port. Select No, Yes or
Default.
Default.
Dialback Mode
A configurable setting that determines where the PBXgateway routes
your calls. There are four different Dialback Modes and the level of
security varies from one to another: Roaming, Disabled, Fixed and
Fixed/Forced. The System Administrator is the only person who can
change the Dialback Mode.
your calls. There are four different Dialback Modes and the level of
security varies from one to another: Roaming, Disabled, Fixed and
Fixed/Forced. The System Administrator is the only person who can
change the Dialback Mode.
ConneX Ch Type
This parameter identifies the port the ConneX session will use to
connect the mobile/remote user to the office gateway. In the case of the
Definity or Meridian protocol, the default will be the current digital port’s
B2 channel (PBX_B2_Static). In the case of the Norstar protocol, the
default link port is the adjacent B1 port (PBX_B1_Static)
Note: If this field is set to disable, ConneX capability is disabled.
connect the mobile/remote user to the office gateway. In the case of the
Definity or Meridian protocol, the default will be the current digital port’s
B2 channel (PBX_B2_Static). In the case of the Norstar protocol, the
default link port is the adjacent B1 port (PBX_B1_Static)
Note: If this field is set to disable, ConneX capability is disabled.
Dialback Number
The telephone number that the PBXgateway uses to reach you on your
analog or mobile phone. Incoming calls to your office extension are
routed to the dialback number that is currently set. .
Note: Dialback number must include prefix (9+ 1 e. g.) necessary to
access outside line.
Note: If necessary, a comma (,) will be used as a pause in the dialstring.
analog or mobile phone. Incoming calls to your office extension are
routed to the dialback number that is currently set. .
Note: Dialback number must include prefix (9+ 1 e. g.) necessary to
access outside line.
Note: If necessary, a comma (,) will be used as a pause in the dialstring.
Idle Timeout
This is the amount of time a channel will be in the Idle mode (connected
but no active calls) before the phone is disconnected. Set this value to
zero to disable the Idle Timeout. Range:0-192 minutes.
but no active calls) before the phone is disconnected. Set this value to
zero to disable the Idle Timeout. Range:0-192 minutes.
Min Password
Length
Length
This parameter ensures the minimum length of the ConneX login
password for security purposes. Also, it provides the following features
for a newly configured user:
The System Administrator can assign a ConneX user an initial password
by entering a value in the Password field of the Port Menu. Also, the
Administrator can let the ConneX user enter their own password by
configuring the 'Min Password Len' parameter. When the user first
attempts to access the ConneX port from their remote phone, they will
be prompted to enter a password with the specified length.
Note: The minimum value for this field is 2 (maximum is 9). To disable
the limitation of password length, leave the field blank.
password for security purposes. Also, it provides the following features
for a newly configured user:
The System Administrator can assign a ConneX user an initial password
by entering a value in the Password field of the Port Menu. Also, the
Administrator can let the ConneX user enter their own password by
configuring the 'Min Password Len' parameter. When the user first
attempts to access the ConneX port from their remote phone, they will
be prompted to enter a password with the specified length.
Note: The minimum value for this field is 2 (maximum is 9). To disable
the limitation of password length, leave the field blank.
Ring Count
Properly setting this ring count will ensure calls are routed to your
Corporate Voice Mail instead of your mobile service provider’s voicemail.
Ring count will dictate the number of audible rings the GW will send to
the remote phone, via dialback before going to your corporate voice
mail.
Set this count at least one ring higher then your service provider’s
voicemail ring count. In most cases a Telco will set their voicemail ring
count to 4 rings. We suggest setting this value to at least 5 rings to
ensure your Corporate Voicemail will receive this unanswered call.
Corporate Voice Mail instead of your mobile service provider’s voicemail.
Ring count will dictate the number of audible rings the GW will send to
the remote phone, via dialback before going to your corporate voice
mail.
Set this count at least one ring higher then your service provider’s
voicemail ring count. In most cases a Telco will set their voicemail ring
count to 4 rings. We suggest setting this value to at least 5 rings to
ensure your Corporate Voicemail will receive this unanswered call.
More...
ADSI Detection
ADSI Detection
Enabled, Disabled. Select Enabled only when the remote client is using
an ADSI enabled RemoteConneX Phone. This will enable
RemoteConneX and allow RemoteConneX Phone user to use the
special phone features.
an ADSI enabled RemoteConneX Phone. This will enable
RemoteConneX and allow RemoteConneX Phone user to use the
special phone features.
ADSI CLID
This item is a RemoteConneX specific feature. This parameter is used to
enable or disable the RemoteConneX Phone to display Caller ID
information.
enable or disable the RemoteConneX Phone to display Caller ID
information.
ConneX Line Keys
This parameter specifies the PBX line appearance keys for the ConneX
port. Please assign this value according to the PBX configurations for
port. Please assign this value according to the PBX configurations for