ONKYO TX-NR801 Manual De Instruções

34

Selecting the Appropriate Setting for Your Connections—Continued

Set the distance from the front right speaker to your 
normal listening position. This can be set between 1 and 
30 feet in 0.5 feet increments (between 0.3 and 9 meters 
in 0.15 meter increments).

e. Surr Right
Set the distance from the surround right speaker to your 
normal listening position. This can be set between 1 and 
30 feet in 0.5 feet increments (between 0.3 and 9 meters 
in 0.15 meter increments).

f. Surr Back R
Set the distance from the surround back right speaker to 
your normal listening position. This can be set between 
1 and 30 feet in 0.5 feet increments (between 0.3 and 9 
meters in 0.15 meter increments).

g. Surr Back L
Set the distance from the surround back left speaker to 
your normal listening position. This can be set between 
1 and 30 feet in 0.5 feet increments (between 0.3 and 9 
meters in 0.15 meter increments).

Note:
If the Surr Back/Zone 2 setting in the Surr Back/Zone 2 
Sub-menu of the Hardware Setup Menu is set to “Zone 
2,” then the Surr Back R and Surr Back L settings will 
not be displayed.

h. Surr Left
Set the distance from the surround left speaker to your 
normal listening position. This can be set between 1 and 
30 feet in 0.5 feet increments (between 0.3 and 9 meters 
in 0.15 meter increments).

i. Subwoofer
Set the distance from the subwoofer to your normal 
listening position. This can be set between 1 and 30 feet 
in 0.5 feet increments (between 0.3 and 9 meters in 0.15 
meter increments).

Use this sub-menu to set the volume for each speaker so 
that each volume is heard by the listener at the same 
level. This is especially important for speaker layouts 
where the left and right speakers are at different dis-
tances or in asymmetrical positions due to room designs 
and configurations. These settings and the distance set-
tings performed in the Speaker Distance Sub-menu are 
vital for creating proper sound space and dynamics.

• These settings cannot be made when the sound is 

muted, when you connect the headphones, and when 
you use multichannel playback.

• You cannot use the MASTER VOLUME dial while 

you perform the Level Calibration settings. These 
settings are inteded to bring sound levels between 
speakers into balance so as to obtain the proper sound 
space.

• This unit supports the THX format and the test tone is 

output at a standard 0 dB (the Absolute Volume value 
is 82). If you usually enjoy listening at a lower level 
than the test tone, be careful of the test tone’s 
sudden big sound. Note that the test tone will be 
output immediately after pressing the ENTER button 
in step 1 below.

Notes:
• Speakers for which you selected “No” or “None” in 

the Speaker Config Sub-menu cannot be selected.

1-3.Level Calibration 

 a.Left         :  0dB 
 b.Center       :  0dB
 c.Right        :  0dB
 d.Surr Right   :  0dB
 e.Surr Back R  :  0dB
 f.Surr Back L  :  0dB
 g.Surr Left    :  0dB
 h.Subwoofer    :  0dB
            Quit:[SETUP]

“3. Level Calibration” on the sub menu 
and then press the ENTER button.
The “Level Calibration” menu appears.
You will hear a pink noise from the front left 
speaker. At this time, the volume of the pink noise 
will automatically increase to a predetermined 
reference level (82).

Note:
Speakers for which you selected “No” or “None” 
in the “Speaker Config” menu will be disabled.

“Left.”
Remember the volume level of this noise and then 
press the 

 cursor button. (Note that this can be 

adjusted to any level between –12 and +12 
decibels in 1 decibel increments. For subwoofer, 
values between –15 and +12 dB can be set.) The 
TX-NR801/TX-NR801E will now emit the pink 
noise from the center speaker.

adjust the volume level of the noise from 
the center speaker so that it is at the same 
level as that emitted from the front left 
speaker. 
You can go back and forth between the speakers 
to help you compare the volume levels.

The TX-NR801/TX-NR801E will now emit the 
pink noise from the front right speaker.