ONKYO TX-SR502 Manual De Instruções
44
Using the Listening Modes
—Continued
If the Surr Back setting is set to anything other than None
in the Speaker Configuration (page 32), and if the sur-
round information in the current input signal is “
in the Speaker Configuration (page 32), and if the sur-
round information in the current input signal is “
3/2.1
”
or “
3/3.1
(you can check the format of a digital input sig-
nal on page 35, “Displaying Source Information.”), you
can determine whether Dolby Digital and DTS material
is played using 6.1-channels or 5.1-channels.
can determine whether Dolby Digital and DTS material
is played using 6.1-channels or 5.1-channels.
Dolby Digital Setting
Auto:
If the source signal contains a Dolby Digital
EX flag, Dolby Digital EX 6.1 is used. If not,
Dolby Digital 5.1 is used.
EX flag, Dolby Digital EX 6.1 is used. If not,
Dolby Digital 5.1 is used.
On:
Dolby Digital EX 6.1 is used regardless of
whether the source signal contains a Dolby
Digital EX flag. You can switch between Dolby
Digital EX and PL IIx Music.
whether the source signal contains a Dolby
Digital EX flag. You can switch between Dolby
Digital EX and PL IIx Music.
Off:
Dolby Digital 5.1 is used even if a Dolby Dig-
ital EX flag is present.
ital EX flag is present.
DTS Setting
Auto:
If the source signal contains a DTS-ES flag,
DTS-ES Discrete (6.1) or DTS-ES Matrix
(6.1) is selected automatically. If not, DTS 5.1
is used.
DTS-ES Discrete (6.1) or DTS-ES Matrix
(6.1) is selected automatically. If not, DTS 5.1
is used.
On:
DTS-ES 6.1 is used regardless of whether the
source signal contains a DTS-ES flag. If the
source signal does contain a DTS-ES flag, you
can select either DTS-ES Discrete or DTS-ES
Matrix. If the source signal does not contain a
DTS-ES flag, you can select DTS+Dolby EX,
PL IIx Music, or DTS+Neo:6.
source signal contains a DTS-ES flag. If the
source signal does contain a DTS-ES flag, you
can select either DTS-ES Discrete or DTS-ES
Matrix. If the source signal does not contain a
DTS-ES flag, you can select DTS+Dolby EX,
PL IIx Music, or DTS+Neo:6.
Off:
DTS 5.1 is used for all DTS sources, even if a
DTS-ES flag is present.
DTS-ES flag is present.
Dolby Digital/DTS setting
(5.1 or 6.1-channel playback)
(5.1 or 6.1-channel playback)
1
Press the [AMP] mode button fol-
lowed by the [SETUP] button.
lowed by the [SETUP] button.
2
Use the Up and Down [
]/[
]
buttons to select “4. Audio
Adjust,” and then press the
[ENTER] button.
Adjust,” and then press the
[ENTER] button.
CD
+10
0
CLEAR
1
2
3
4
5
6
7
8
9
V1
V2
V3
DVD
MULTI CH
--/---
TAPE
TUNER
INPUT
I
+
-
ENTER
SET
UP
GUI
DE
RE
TURN
EXIT
CINE FLTR
LEVEL
-
LEVEL
+
CH SEL
TEST TONE
DSP
DIRECT
STEREO
ALL ST
SURR
L NIGHT
TO
P M
ENU
MEN
U
VOL
+
-
CDR
SAT
AMP
+
_
TV
VCR
CABLE
DVD
CD
MD
DISC
CH
TONE
TUNER/
TAPE
TAPE
DISPLAY
TV
INPUT
INPUT
PREV
CH
CH
DIMMER
SLEEP
RANDOM
SP A
SP B
MUTING
ANGLE
SEARCH
SUBTITLE
AUDIO
MEMORY
A-B
REPEAT
ON
STANDBY
T V
TV CH
T V VOL
RC-567M
REC
LAST M
REMOTE MODE
OPEN/CLOSE
DSP
VIDEO OFF
LEVEL
-
LEVEL
+
SETUP
AMP
ENTER
SURR
AMP
ENTER
ENTER
3
When playing Dolby Digital
material:
material:
Use the Up and Down [
]/[
]
buttons to select “SB (Dolby D),”
and then use the Left and Right
[
and then use the Left and Right
[
]/[
] buttons to select “Auto,”
“On,” or “Off.”
When playing DTS material:
Use the Up and Down [
]/[
]
buttons to select “SB (DTS),” and
then use the Left and Right [
then use the Left and Right [
]/
[
] buttons to select “Auto,”
“On” or “Off.”
4
Press the [SETUP] button.
Setup closes.
5
Use the remote controller’s
[SURR] button, or the TX-SR502/
TX-SR502E’s LISTENING MODE
[
[SURR] button, or the TX-SR502/
TX-SR502E’s LISTENING MODE
[
]/[
] buttons to select the
required listening mode.
ENTER
ENTER
SURR
TX-SR502_En.book Page 44 Tuesday, February 17, 2004 12:14 PM