Sony LBT-SH2000 Manual

model name [LBT-SH2000]

[4-273-674-81(1)] US

filename[D:\NORM'S JOB\SONY HA\SO120012\LBT-
SH2000\4273674811_US\US080ADD.fm]

masterpage:Left

• Completely disconnect the power cord (mains 

lead) from the wall outlet (mains) if it is not 
going to be used for an extended period of 
time. When unplugging the unit, always grip 
the plug. Never pull the cord itself.

• Should any solid object or liquid get into the 

system, unplug the system, and have it 
checked by qualified personnel before 
operating it again.

• AC power cord must be changed only at the 

qualified service shop.

• Avoid looking directly at the lighting on the 

LED speakers for too long. Doing so may be 
harmful to your health.

• Do not place the system in an inclined 

position or in locations that are extremely hot, 
cold, dusty, dirty, or humid or lacking 
adequate ventilation, or subject to vibration, 
direct sunlight or a bright light.

• Be careful when placing the unit or speakers 

on surfaces that have been specially treated 
(for example, with wax, oil, polish) as staining 
or discoloration of the surface may result.

• If the system is brought directly from a cold to 

a warm location or is placed in a very damp 
room, moisture may condense on the lens 
inside the unit, and cause the system to 
malfunction. In this situation, remove the 
disc, and leave the system turned on for about 
an hour until the moisture evaporates.

• Heat buildup on the unit during operation is 

normal and is not a cause for alarm.

• Do not touch the cabinet if it has been used 

continuously at a high volume because the 
cabinet may have become hot.

• Do not obstruct the ventilation holes.

This speaker system is not magnetically 
shielded, and the picture on nearby TV sets may 
become magnetically distorted. In this situation, 
turn off the TV, wait 15 to 30 minutes, and turn 
it back on. If there is no improvement, move the 
speakers far away from the TV.

Clean this system with a soft cloth slightly 
moistened with a mild detergent solution. 
Do not use any type of abrasive pad, scouring 
powder, or solvent, such as thinner, benzine, 
or alcohol.

POWER OUTPUT AND TOTAL 
HARMONIC DISTORTION:
With 4 ohm loads, both channels driven, 
from 120 – 10,000 Hz; rated 240 watts per 
channel minimum RMS power, with no 
more than 0.7% total harmonic distortion 
from 250 milliwatts to rated output.

The following are measured at AC 120 V, 
60 Hz
Power output (rated): 

High channel
300 W + 300 W (at 4 

:, 1 kHz, 

1% THD)
Low channel
300 W + 300 W (at 4 

:, 100 Hz, 

1% THD)

RMS output power (reference): 

High channel
500 W + 500 W (per channel at 4 

:, 

1 kHz)
Low channel
500 W + 500 W (per channel at 4 

:, 

100 Hz)

Inputs
PC (AUDIO IN) L/R, TV (AUDIO IN) L/R, 
DVD/SAT (AUDIO IN) L/R, GAME 
(AUDIO IN) L/R

Voltage 2 V, impedance 47 k

:

MIC

Sensitivity 1 mV, impedance 10 k

:

 A, 

 B port: Type A

Supported bit rate

MP3 (MPEG 1 Audio Layer-3): 
32 kbps – 320 kbps, VBR
WMA: 48 kbps – 192 kbps
AAC: 48 kbps – 320 kbps