KitchenAid 1000-Watt Microwave with 7 Sensor Functions - 30" Guia Da Instalação

NOTE: Secure the mounting plate to the wall at both end 

holes drilled into the wall studs and/or drywall using either  

3/16-24 x 3" round-head bolts and toggle nuts or 1/4 x 2" 

lag screws.
Refer to illustrations in “Possible Wall Stud Configurations” 

in “Locate Wall Stud(s)” section.

NOTE: The mounting plate must be secured to the wall 

on at least 1 wall stud as well as at both ends.
1.  With the support tabs of the mounting plate facing forward, 

insert 3/16-24 x 3" round-head bolts through both end holes 

of mounting plate.

2.  Start toggle nuts on bolts from the back of the mounting 

plate. Leave enough space for the toggle nuts to go 

through the wall and to open.

3.  Position mounting plate on the wall.
4.  Push the 2 bolts with toggle nuts through the drywall, 

and finger tighten the bolts to make sure toggle nuts 

have opened against drywall.

5.  Insert lag screw(s) into the hole(s) drilled into wall stud(s) 

in Step 2 of “Installation for No Wall Studs at End Holes” 

in the “Drill Holes in Rear Wall” section.

6.  Check alignment of mounting plate, making sure it is level.
7.  Securely tighten all lag screws and bolts.

1.  With the support tabs of the mounting plate facing forward, 

insert a 3/16-24 x 3" round-head bolt through the end 

hole that fits over the 5/8" (16 mm) hole drilled in Step 3 

of “Installation for Wall Stud at One End Hole” in the “Drill 

Holes in Rear Wall” section.

2.  Start a toggle nut on the bolt from the back of the mounting 

plate. Leave enough space for the toggle nut to go through 

the wall and to open.

3.  Position mounting plate on the wall.
4.  Push the bolt with toggle nut through the drywall, and 

finger tighten the bolt to make sure toggle nut has 

opened against drywall.

5.  Insert a lag screw into the remaining end hole.
6.  If installing on a second wall stud, insert a lag screw into 

the other hole drilled in Step 2 of “Installation for Wall Stud 

at One End Hole” in the “Drill Holes in Rear Wall” section.

7.  Check alignment of mounting plate, making sure it is level.
8.  Securely tighten the lag screw(s) and bolt.

1.  Position mounting plate on the wall.
2.  Insert lag screws into both end holes.
3.  Check alignment of mounting plate, making sure it is level.
4.  Securely tighten the lag screws.

1.  Disconnect power to outlet.
2.  Remove all contents from upper cabinet.
3.  Place Upper Cabinet Template against the bottom of 

the upper cabinet, and attach with tape or thumbtacks. 

Make sure the template centerline aligns with the vertical 

centerline on the rear wall.
The “rear wall” arrows must be against the rear wall so that 

the holes cut into the upper cabinet align with the holes in 

the top of the microwave oven.

 

■

If the upper cabinet has a frame around it, trim the template 

edges so that it fits inside the frame, against the upper 

cabinet bottom. The template has trim lines to use as guides.

 

■

If the wall behind the microwave oven (as installed) has 

a partial wall covering (for example, tile backsplash), be 

sure the “Rear Wall” arrows align to the thickest part of 

the rear wall (for example, the thickness of the tiles rather 

than the drywall).

4.  Make sure the 10" (25.4 cm) dimension from the rear wall 

to points “D” and “E” on the template is maintained.