Cisco Cisco IOS Software Release 12.2
23
Related Documentation
OL-3177-01B
Related Documentation
Related Documentation
The software described in these release notes runs on several Cisco NI-2 DSLAM platforms,
including the Cisco 6015, Cisco 6160, and Cisco 6260 DSLAMs.
including the Cisco 6015, Cisco 6160, and Cisco 6260 DSLAMs.
A complete list of all DSL hardware product related documentation is available at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/dsl_prod/index.htm
A complete list of all DSL Cisco IOS product related documentation is available at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/dsl_prod/ios_dsl/index.htm
In the Cisco ATM software manuals, look for information pertaining to the LightStream 1010, which uses
the same software base as the Cisco NI-2 DSLAMs. ATM manuals are available at the following URL:
the same software base as the Cisco NI-2 DSLAMs. ATM manuals are available at the following URL:
http://www.cisco.com/univercd/cc/td/doc/product/atm/index.htm
CSCdv38294
VPI/VCI values for provisioned PVC do not match the provisioned values when
you select a VCI value of 0 for any non-terminating PVC (that is, a PVC not
terminating at atm0/0).
you select a VCI value of 0 for any non-terminating PVC (that is, a PVC not
terminating at atm0/0).
CSCdv80202
The shdsl profile has a different format between Cisco IOS Release 12.1(7)DA and
Cisco IOS Release 12.2(5).
Cisco IOS Release 12.2(5).
CSCdv86663
When you configure an interface bandwidth statement on a Cisco 6260 DSLAM
ATM interface, the default bandwidth value for the interface as seen in the
show interface atm command may appear in the show running-config output.
ATM interface, the default bandwidth value for the interface as seen in the
show interface atm command may appear in the show running-config output.
CSCdw03128
Cisco 6260 DSLAM SNMP agent returns incorrect ifType for SHDSL interfaces.
CSCdw25440
Using the command show atm vc interface atm slot/port vpi vci where vpi and vci
are the VPI and VCI numbers in a SVC configuration can cause the DSLAM to
reload. This usually happens when the CPE is connected but the SVC is not yet
established.
are the VPI and VCI numbers in a SVC configuration can cause the DSLAM to
reload. This usually happens when the CPE is connected but the SVC is not yet
established.
CSCdw34798
Invalid cells are passed to network port on a valid VC. The 4xDMT line card does
not discard cells with HEC errors and stamps each cell going to the DSLAM with
a valid HEC. The switch can then pass these corrupt cells out the WAN interface if
they appear to have a valid and provisioned VPI and VCI.
not discard cells with HEC errors and stamps each cell going to the DSLAM with
a valid HEC. The switch can then pass these corrupt cells out the WAN interface if
they appear to have a valid and provisioned VPI and VCI.
CSCdw41743
After 54 days of uptime, the system experienced an unexpected reload immediately
preceded by the messages: System reloads with message SYS-2-WATCHDOG
process=IMA CORE.
preceded by the messages: System reloads with message SYS-2-WATCHDOG
process=IMA CORE.
CSCdw47576
An NI-2 DSLAM reloads after a few ALIGN-1-FATAL error messages.
CSCdw65903
An error can occur with management protocol processing. Please use the following
URL for further information:
URL for further information:
Table 9
Caveats Resolved in Cisco IOS Release 12.2(7)DA (continued)
Caveat Number
Description