Cisco Cisco 2106 Wireless LAN Controller
13
Release Notes for Cisco Wireless LAN Controllers and Lightweight Access Points for Release 4.2.173.0
OL-31336-01
Important Notes
Multicast Limitations
Multicast is not supported on access points that are connected directly to the local port of a 2000 or 2100
series controller.
series controller.
MAC Filtering for WGB Wired Clients
Controller software release 4.1.178.0 or later enables you to configure a MAC-filtering IP address for a
workgroup bridge (WGB) wired client to allow passive WGB wired clients, such as terminal servers or
printers with static IP addresses, to be added and remain in the controller’s client table while the WGB
is associated to a controller in the mobility group. This feature, activated by the config macfilter
ipaddress MAC_address IP_address CLI command, can be used with any passive device that does not
initiate any traffic but waits for another device to start communication.
workgroup bridge (WGB) wired client to allow passive WGB wired clients, such as terminal servers or
printers with static IP addresses, to be added and remain in the controller’s client table while the WGB
is associated to a controller in the mobility group. This feature, activated by the config macfilter
ipaddress MAC_address IP_address CLI command, can be used with any passive device that does not
initiate any traffic but waits for another device to start communication.
This feature allows the controller to learn the IP address of a passive WGB wired client when the WGB
sends an IAPP message to the controller that contains only the WGB wired client’s MAC address. Upon
receiving this message from the WGB, the controller checks the local MAC filter list (or the anchor
controller’s MAC filter list if the WGB has roamed) for the client’s MAC address. If an entry is found
and it contains an IP address for the client, the controller adds the client to the controller’s client table.
sends an IAPP message to the controller that contains only the WGB wired client’s MAC address. Upon
receiving this message from the WGB, the controller checks the local MAC filter list (or the anchor
controller’s MAC filter list if the WGB has roamed) for the client’s MAC address. If an entry is found
and it contains an IP address for the client, the controller adds the client to the controller’s client table.
Note
Unlike the existing MAC filtering feature for wireless clients, you are not required to enable MAC
filtering on the WLAN for WGB wired clients.
filtering on the WLAN for WGB wired clients.
Note
WGB wired clients using MAC filtering do not need to obtain an IP address through DHCP to be added
to the controller’s client table.
to the controller’s client table.
CKIP Not Supported with Dynamic WEP
In controller software release 4.1.185.0 or later, CKIP is supported for use only with static WEP. It is not
supported for use with dynamic WEP. Therefore, a wireless client that is configured to use CKIP with
dynamic WEP is unable to associate to a wireless LAN that is configured for CKIP. Cisco recommends
that you use either dynamic WEP without CKIP (which is less secure) or WPA/WPA2 with TKIP or AES
(which are more secure).
supported for use with dynamic WEP. Therefore, a wireless client that is configured to use CKIP with
dynamic WEP is unable to associate to a wireless LAN that is configured for CKIP. Cisco recommends
that you use either dynamic WEP without CKIP (which is less secure) or WPA/WPA2 with TKIP or AES
(which are more secure).
Synchronizing the Controller and Location Appliance
For controller software release 4.2 or later, if a location appliance (release 3.1 or later) is installed on
your network, the time zone must be set on the controller to ensure proper synchronization between the
two systems. Also, Cisco highly recommends that the time be set for networks that do not have location
appliances. Refer to Chapter 4 of the Cisco Wireless LAN Controller Configuration Guide, Release 4.2
for instructions for setting the time and date on the controller.
your network, the time zone must be set on the controller to ensure proper synchronization between the
two systems. Also, Cisco highly recommends that the time be set for networks that do not have location
appliances. Refer to Chapter 4 of the Cisco Wireless LAN Controller Configuration Guide, Release 4.2
for instructions for setting the time and date on the controller.
Note
The time zone can be different for the controller and the location appliance, but the time zone delta must
be configured accordingly, based on Greenwich Mean Time (GMT).
be configured accordingly, based on Greenwich Mean Time (GMT).