Cisco Headend System Release 2.7
Chapter 1 Why Choose System Release 3.8?
16
4019365 Rev B
CR 91265: Multicast Session Setup Fails on GQAM TSR Port
If a user tries to set up a DNCS Multicast Session where the RF port has a TSR
defined as Multicast IP + UDP Port, the GQAM issues fails the session request and
displays 0x90020010 "Route Conflict Ouput."
defined as Multicast IP + UDP Port, the GQAM issues fails the session request and
displays 0x90020010 "Route Conflict Ouput."
CR 91794: CCardServer Doesn't Save New Host from RegisterHost Transation if
HostChangeCount=MHCCA
HostChangeCount=MHCCA
The user will not be able to modify the host for a CableCARD/Host pair using the
RegisterHost transaction from a billing system when the CableCARD Host Change
Count value equals the system's Max Host Change Count Allowed value. The
RegisterHost transaction will reset the CableCARD Host Change Count value to
zero, but the host ID will not be updated for this CableCARD module.
RegisterHost transaction from a billing system when the CableCARD Host Change
Count value equals the system's Max Host Change Count Allowed value. The
RegisterHost transaction will reset the CableCARD Host Change Count value to
zero, but the host ID will not be updated for this CableCARD module.
Workarounds:
If the MHCCA does not equal 0, the user can send the same RegisterHost
transaction a second time. The Host ID will update with the second transaction
following the CableCARD Host Change Count being reset to zero. This second
transaction will cause the Host Change Count to increment to a value of one (1).
transaction a second time. The Host ID will update with the second transaction
following the CableCARD Host Change Count being reset to zero. This second
transaction will cause the Host Change Count to increment to a value of one (1).
The user can also use CableCARD WUI to edit the existing CableCARD/Host
record by changing the host ID in the CableCARD WUI on the DNCS. The
CableCARD WUI edit Host ID will work regardless of the CableCARD Host
Change Count value and MHCCA value.
record by changing the host ID in the CableCARD WUI on the DNCS. The
CableCARD WUI edit Host ID will work regardless of the CableCARD Host
Change Count value and MHCCA value.
CR 92130: Table-Based Session Upload Feature Does Not Validate UDP Port Values
The table-based session upload feature allows users to enter UDP port values above
65535, even though these values are not valid. If a user enters values above 65,535
(for example, if the user creates a csv file and forgets the comma following the UDP
port), the system creates a new, lower value for that file. For example, 65,536 would
be saved as 0, 65,537 would be saved as 1, and so on.
65535, even though these values are not valid. If a user enters values above 65,535
(for example, if the user creates a csv file and forgets the comma following the UDP
port), the system creates a new, lower value for that file. For example, 65,536 would
be saved as 0, 65,537 would be saved as 1, and so on.
CR 92748: emmDistributor Default Average Packets Is Incorrect
The default average packet count is set to be 1. This value can cause cycle times to
exceed the targeted cycle time, in some cases by a factor of two. For instance a 7-day
set cycle time can become a 14-day cycle time.
exceed the targeted cycle time, in some cases by a factor of two. For instance a 7-day
set cycle time can become a 14-day cycle time.
CR 94077: Loss of DSG Filter for OCAP Object Carousel
After boot on all ASPEN RNG platforms 200/150/100, the filter for OCAP Object
Carousel does not always display in diagnostic filter pages. This occurs periodically
across all hubs and both SVT ASPEN headends. As a result there is no info
populated on diagnostic page 15 - Object Carousel Information when this occurs.
Carousel does not always display in diagnostic filter pages. This occurs periodically
across all hubs and both SVT ASPEN headends. As a result there is no info
populated on diagnostic page 15 - Object Carousel Information when this occurs.