atlinks temporis mini Manual Do Utilizador

Your telephone is designed to give you flexibility of use, and high 
quality performance. To get the most from your new telephone, 
we suggest that you take a few minutes to read through this 
instruction manual.
If you have any questions or problems, consult the Troubleshooting 
Tips for the solution.

Your package should contain the following items:

Base unit with handset

You need a RJ11C type modular jack, which is 
the most common type of phone jack and might 
look like the one pictured here. If you don’t have 
a modular jack, call your local phone company 
to find out how to get one installed.

Your telephone should be placed on a level surface such as a desk top, 
or you can mount it on a wall , A desktop /wall mounting pedestal is built 
into the base of the phone.

Connect the telephone line cord to a modular telephone jack.
Slide the RINGER switch (on the handset ) to ON.
Set PULSE/ TONE switch (on the handset ) to TONE for touch-tone 
service, or set it to PULSE for rotary service. If you don’t know which 
type of service you have, check with the phone company.

1.
2.
3.

Your telephone may also be mounted on a wall plate (not  included).

Slip the mounting holes (on the bottom 
of the base) over the wall plate posts and 
firmly slide the unit down into place.
Plug the telephone line cord into a 
modular wall phone jack.

1.

2.

Be sure the RINGER switch is set to the On (       ) position.
When the phone rings. lift the handset and begin your conversation.
Slide the RINGER switch to the Off (       ) position when you do not want 
to be interrupted by the phone ringing.

1.
2.
3.

You may control the ringer volume level with the switch located on the 
right side of the handset.
      = ringer tone will be loud.
      = telephone will not ring.

Lift the handset and wait for a dial tone.
Dial the telephone number you wish to call.

1.
2.

This unit redials up to 32 digits. To 
automatically redial the last number You 
called: 

Pick up the handset to get a dial tone.
Press redial.

If you have Pulse ( rotary ) service ,and 
want to access customer calling services 
that require  touch –tone dialing ,such as 
getting information from a local bank ,you 
can use this feature.

Press the TONE button ( * ) after you 
have connected to the service in order 
to enable touch –tone dialing. 
When you hang up, the phone 
automatically returns to Pulse dialing 
mode.

1.
2.

1.

2.

TONE button

PROBLEM                                                              SOLUTION
No dial tone 
Won’t dial out

Check hook switch to make sure it pops up.
Make sure TONE / PULSE is set to correct position.

•
•

Phone doesn’t ring

Make sure RINGER switch is set to On (         )
You might have too many phones on one line.

•
•

Feedback when 
dialing in PULSE mode

This is normal, power fluctuates with phone 
outpulsing.

•

Can’t be heard by 
other party

Make sure phone cord is securely plugged in.
Make sure other phones aren’t off the hook 
at the same time you’re using the phone.
It is normal for the  volume to drop when 
additional phones are used at the same time.

•
•

To keep your phone working and looking good ,follow these guidelines;

Avoid putting near heating appliances and devices that generate 
electrical noise (for example , motors and fluorescent lamps)
DO NOT expose to direct sunlight or moisture.
Avoid dropping and other rough treatment.
Never use a strong cleaning agent or abrasive powder because this 
will damage the finish.
Retain the original package in case you need to ship it at a later date.

•

•
•
•

•

Used equipment must be disposed of in compliance with 
current environmental protection regulations. You should 
return it to your reseller or dispose of it in an approved 
recycling centre.

Model Temporis mini-EX

XXXXXXXX (Rev.0 E/S)

09-31

Printed in China

Tone/Pulse

Switch

Ringer

on/off

Redial