ATIKA ghb 760 Brochura
If the machine’s filling hopper or ejection slot is blocked
stop the engine, disconnect the spark plug connector and
wait until the tools are stationary before removing residual
material from the filling hopper or ejection slot.
stop the engine, disconnect the spark plug connector and
wait until the tools are stationary before removing residual
material from the filling hopper or ejection slot.
Check the machine for possible damage:
16
−
Before further use of the machine the safety devices
must be checked carefully for their proper and intended
function.
must be checked carefully for their proper and intended
function.
−
Check whether movable parts function perfectly and do
not stick or whether parts are damaged.
not stick or whether parts are damaged.
All parts must
be correctly installed and fulfil all conditions to ensure
perfect operation of the machine.
perfect operation of the machine.
−
Damaged guards and parts must be properly repaired
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
or exchanged by a recognized, specialist workshop;
insofar as nothing else is stated in the instructions for
use.
−
Damaged or illegible safety labels should be replaced
immediately.
immediately.
Store unused equipment in a dry, locked place out of the
reach of children.
reach of children.
Do not allow any tool key to be plugged in!
Before switching on, check always that wrenches and
adjusting tools are removed.
Before switching on, check always that wrenches and
adjusting tools are removed.
Do not repair the device unless you are qualified for such
kind of work.
kind of work.
Do not carry out repair operations on the machine other
than those described in section “Maintenance” but contact
the manufacturer or authorized customer service centres.
than those described in section “Maintenance” but contact
the manufacturer or authorized customer service centres.
Local regulations – especially regarding protective
measures – must be observed.
measures – must be observed.
Use only original spare parts. Accidents can arise for the
user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.
user through the use of other spare parts. The
manufacturer is not liable for any damage or injury
resulting from such action.
Safe handling with fuels
Fuels and fuel vapours are inflammable and may
cause serious injury on the skin or when inhaled.
Therefore be careful and provide sufficient
ventilation when handling with fuels.
Stop the engine and allow the garden shredder to cool
down before fuelling it.
down before fuelling it.
Do not smoke and avoid open flames when fuelling.
Wear gloves when fuelling.
Do not fuel in closed rooms (risk of explosion).
Avoid spilling of fuel or oil.
Clean the garden shredder
immediately when you have spilled fuel or oil.
Change your
clothes immediately when you have spilled fuel or oil on
them.
them.
Make sure that no fuel can come into the soil.
Carefully close the tank cap after fuelling and check that it
does not get loose during operation.
does not get loose during operation.
Check that there is no leakage on the tank cap and fuel
lines.
lines.
If there are leaks this device may not be started.
Only transport and store fuels in containers approved and
identified for this.
identified for this.
Keep children away from fuels.
Do not handle and store fuels close to combustible and
highly inflammable materials as well as sparks and open
flames.
highly inflammable materials as well as sparks and open
flames.
Go away at least three metres from the fuelling place to
start the device.
start the device.
A
A
s
s
s
s
e
e
m
m
b
b
l
l
y
y
Two persons are required for assembly.
Remove the both screws.
Attach the storage box.
Mount the carrying handles.
You will need: 4 pcs tallow-drop screw M8x35, 4 pcs
self-locking hexagon nut, 16 pcs washer A8.4.
Second person:
Tilt the garden shredder towards yourself.
Other person:
Remove the screw.
Put the ejection slot (7) between plate and ejection
Remove the screw.
Put the ejection slot (7) between plate and ejection
screen (6).
Guide the screw M8x205 through plate, ejection slot
and screen. Secure the screws with washer A8.4, lock
washer A8 and hexagon nut M8.
washer A8 and hexagon nut M8.
Do not firmly tighten the hexagon nut.
Fold up the ejection slot (7).
Then install the support (12).
Install at first the supports RH and LH using the
screws M8x20, washer A8.4, lock washer A8 and
hexagon nut M8.
hexagon nut M8.
Then place the distance sleeve (39) and guide the
screw M8x205 through it.
Secure the screw with
washer A8.4, lock washer A8 and hexagon nut M8.
Firmly tighten all screw connections.
Then, the other person tilts the garden shredder to the
opposite direction.
Guide the screws M8x205 through the axle support
RH (38) and then through the device.
Position the distance sleeves and guide the screws
through them.
Secure the screws with washer A8.4,
lock washer A8 and hexagon nut M8.
Guide the axle (10) through the axle support.
Then place on the axle support LH (37).
Put the wheels on the axle.
Secure the wheels using the lock washer A5 and the
wheel cap (40).
B
B
e
e
f
f
o
o
r
r
e
e
t
t
h
h
e
e
f
f
i
i
r
r
s
s
t
t
s
s
t
t
a
a
r
r
t
t
-
-
u
u
p
p
The garden shredder is supplied without petrol and oil in
it.
Fuel the garden shredder as described under ”Fuelling”.
it.
Fuel the garden shredder as described under ”Fuelling”.