Yamaha EMX66M Manual Do Utilizador
Basic Operation
19
EMX66M—Owner’s Manual
Basic Operation
This section explains basic operation of the EMX66M.
Connecting microphones
and instruments
and instruments
1
Before connecting mics or instruments,
make sure that the power of all equip-
ment (where applicable) is turned off.
Also make sure that the level controls of
each channel of the EMX66M and the
MASTER control of the MAIN section are
turned down.
make sure that the power of all equip-
ment (where applicable) is turned off.
Also make sure that the level controls of
each channel of the EMX66M and the
MASTER control of the MAIN section are
turned down.
2
Connect cables to your mics and instru-
ments, and insert the other end of the
cable firmly into the appropriate Low-Z/
Hi-Z jack (channels 1–4) or the MIC jack
(channels 5–6), LINE jack (channels 5),
Super Hi-Z jack (channels 6).
ments, and insert the other end of the
cable firmly into the appropriate Low-Z/
Hi-Z jack (channels 1–4) or the MIC jack
(channels 5–6), LINE jack (channels 5),
Super Hi-Z jack (channels 6).
3
Turn the power on in the order of periph-
eral devices ➞ EMX66M.
eral devices ➞ EMX66M.
4
Set the MAIN section MASTER control to
the “√
the “√
√
√
√
” position.
5
While speaking into the mic (while play-
ing the instrument), adjust the channel
LEVEL control so that the 0 LED of the
MAIN section peak level meter lights
occasionally.
Repeat this step for each channel.
ing the instrument), adjust the channel
LEVEL control so that the 0 LED of the
MAIN section peak level meter lights
occasionally.
Repeat this step for each channel.
6
If you wish to adjust the tone of each
channel, rotate the equalizer controls as
desired.
channel, rotate the equalizer controls as
desired.
7
Use the MAIN section graphic equalizer
to adjust the tone.
to adjust the tone.
8
Use the MAIN MASTER control to adjust
the overall volume.
the overall volume.
Monitoring
By connecting a powered monitor speaker to the
MONITOR OUTPUT, you can create a monitor
mix independent of the MAIN mix, since the
input channel MONITOR controls are not
affected by the LEVEL controls.
MONITOR OUTPUT, you can create a monitor
mix independent of the MAIN mix, since the
input channel MONITOR controls are not
affected by the LEVEL controls.
1
Set the MONI MASTER control to the “√
√
√
√
”
position.
2
While speaking into a connected mic, or
playing a connected instrument, adjust
the MONITOR control of the input chan-
nel that you want to monitor.
Repeat this procedure for each channel.
playing a connected instrument, adjust
the MONITOR control of the input chan-
nel that you want to monitor.
Repeat this procedure for each channel.
3
Use the MONI MASTER control to set the
overall level of the monitor mix.
overall level of the monitor mix.
Using the digital effect
The EMX66M has a built-in digital effect, allow-
ing reverberation or ambiance to be added to
vocals or instrumental sounds.
ing reverberation or ambiance to be added to
vocals or instrumental sounds.
1
Press the DIGITAL EFFECT ON switch of
the DIGITAL EFFECT section.
the DIGITAL EFFECT section.
2
Use the effect select switches of the DIGI-
TAL EFFECT section to select the effect
type.
TAL EFFECT section to select the effect
type.
VOCAL ECHO 1, 2 .....Echo appropriate for vocals.
VOCAL REVERB 1, 2 ...Reverb appropriate for vocals.
HALL 1, 2 .................. Reverb typical of a hall.
ROOM ....................... Reverb typical of a room.
PLATE .........................Plate echo-like reverberation
VOCAL REVERB 1, 2 ...Reverb appropriate for vocals.
HALL 1, 2 .................. Reverb typical of a hall.
ROOM ....................... Reverb typical of a room.
PLATE .........................Plate echo-like reverberation
3
Set the MAIN EFFECT RTN control to the
“√
“√
√
√
√
” position.
4
Raise the EFFECT control of the channels
to which you wish to apply the digital
effect.
to which you wish to apply the digital
effect.
5
Use the MAIN/MONITOR section EFFECT
RTN control to adjust the level of the
sound processed by the effect.
RTN control to adjust the level of the
sound processed by the effect.
Note: When connecting a line level device to
channels 1–4, turn on the PAD switch.
You cannot use a channel’s Low-Z and Hi-Z
jacks at the same time. The MIC and LINE
jacks, or the MIC and Super Hi-Z jacks, how-
ever, can be used at the same time.
channels 1–4, turn on the PAD switch.
You cannot use a channel’s Low-Z and Hi-Z
jacks at the same time. The MIC and LINE
jacks, or the MIC and Super Hi-Z jacks, how-
ever, can be used at the same time.
Note: When turning the power off, reverse this
sequence.
sequence.
Note: If the effect sound is distorted even if the
EFFECT RTN turned all the way down, lower
the EFFECT controls of each channel.
EFFECT RTN turned all the way down, lower
the EFFECT controls of each channel.