Yamaha YSP-4100BL Manual Do Utilizador

You can adjust this parameter only when “5BeamPlus2”, 
“5 Beam” or “3 Beam” is selected in “BEAM MODE” 
(page 23).

y

• To adjust the volume of each channel, see “CHANNEL 

LEVEL” (page 37)

Choices: OFF*, ON
• Select “ON” to configure the sound direction.

Adjust the image location for the front left 
channel (LEFT).
The higher the percentage, the louder the output from 
the center

Adjust the image location for the front right 
channel (RIGHT).
The higher the percentage, the louder the output from 
the center

■ TONE CONTROL (Tone control)

→ SOUND SET MENU → TONE 

CONTROL
Use to adjust the tonal quality of sound beams.

TREBLE (Treble)
Use to adjust the high-frequency response.
Choices: –10.0 dB to +10.0 dB
Initial setting: 0.0 dB

BASS (Bass)
Use to adjust the low-frequency response.
Choices: –10.0 dB to +10.0 dB
Initial setting: 0.0 dB

■ SUBWOOFER SET (Subwoofer settings)

→ SOUND SET MENU → 

SUBWOOFER SET
Use to configure the subwoofer settings.

BASS OUT (Bass out)
Select where to output low-frequency effect (LFE) and 
low-frequency (bass) signals.
Choices: SUBWOOFER, FRONT OR AUTO*

• Select SUBWOOFER if you connect a subwoofer with 

a subwoofer cable. LFE and low-frequency signals 
from other channels are directed to the subwoofer.

• Select FRONT OR AUTO if you do not use a 

subwoofer or connect a subwoofer by wireless. LFE 
and low-frequency signals from other channels are 
directed to the front right and left channels when you 
do not use a subwoofer. They are directed to the 
subwoofer automatically when a wireless connection 
between a subwoofer and this unit is established 
properly. If the wireless connection is cut off, they are 
directed to the front channels automatically.

CROSS OVER (Crossover)
When “BASS OUT” is set to “SUBWOOFER”, you can 
use this feature to select a crossover (cutoff) frequency for 
all low-frequency signals. All frequencies below the 
selected frequency will be sent to the subwoofer position.
Choices: 80Hz, 100Hz, 120Hz*

LFE LEVEL (Low-frequency effect level)
Adjust the output level of the low-frequency effect (LFE) 
channel according to the capacity of your subwoofer. This 
setting is effective only when this unit decodes Dolby 
Digital or DTS signals.
Choices: –20 dB to 0 dB*

DISTANCE (Distance)
Adjust the distance of the subwoofer from the listening 
position.
Choices: 0.3 m to 15.0 m (1.0 ft to 50.0 ft)
Initial setting: 3.0 m (10.0 ft)

■ AUDIO DELAY (Audio delay)

→ SOUND SET MENU → AUDIO 

DELAY
Use to adjust delay in output timing between video signals 
and audio signals.

AUTO LIP SYNC (Automatic lipsync)
Select whether to automatically adjust the audio output 
delay when a TV that supports the automatic lipsync is 
connected to the HDMI OUT jack of this unit.
Choices: ON*, OFF
• Select ON if the TV connected to the HDMI OUT jack 

of this unit supports the automatic lipsync. The audio 
output delay is automatically adjusted.

• Select OFF if the TV connected to the HDMI OUT 

jack of this unit does not support the automatic lipsync 
or you want to disable the automatic lipsync. You can 
manually adjust the audio output delay in “HDMI”.

TV
Adjust the audio output delay applied to signals input 
from the TV jacks.
Control range: 0 msec* to 400 msec

HDMI
Manually adjust the audio output delay applied to signals 
input from the HDMI IN jacks. This setting is effective 
only when “AUTO LIP SYNC” is set to “OFF”
Control range: 0 msec to 400 msec
Initial setting: 30msec

AUX1/2
Adjust the audio output delay applied to signals input 
from the AUX1/2 jacks.
Control range: 0 msec to 400 msec
Initial setting: 30msec