Digitech vocalistvr Manual Do Utilizador
8
Setting the Input and Output levels
Input Level
With a microphone or line level source connected to ACCESS, sing or play back a track. Bring
up the input level until the level LED lights orange. Too much input level, and the LED will be
red. Too little input level, and the LED will only light green, never lighting orange. If there are
momentary flickers of red, your signal level will remain clean.
With a microphone or line level source connected to ACCESS, sing or play back a track. Bring
up the input level until the level LED lights orange. Too much input level, and the LED will be
red. Too little input level, and the LED will only light green, never lighting orange. If there are
momentary flickers of red, your signal level will remain clean.
Output Level
The only level setting you need to do on the output is with the output level switch on the back
panel of ACCESS. This allows you to match ACCESS’ output to the sensitivity of your mixer
input. When the switch is pushed in (-10dBu) ACCESS is operating at line level. When the
switch is out (+4dBu) then ACCESS will produce a higher level.
The only level setting you need to do on the output is with the output level switch on the back
panel of ACCESS. This allows you to match ACCESS’ output to the sensitivity of your mixer
input. When the switch is pushed in (-10dBu) ACCESS is operating at line level. When the
switch is out (+4dBu) then ACCESS will produce a higher level.
note: generally this can be set at +4, but if your mixer is distorting, ACCESS’ output level
should be reduced to -10dBu.
should be reduced to -10dBu.
Loading Presets
The Vocalist ACCESS contains 50 factory presets. To select a preset use Data Entry Knob to
scroll through presets. The presets are loaded automatically as you scroll through them. Edited
presets can be saved over top of factory presets as user presets. See ‘Storing Presets’ for further
details. The LCD display shows preset information in the following way:
scroll through presets. The presets are loaded automatically as you scroll through them. Edited
presets can be saved over top of factory presets as user presets. See ‘Storing Presets’ for further
details. The LCD display shows preset information in the following way:
The first two characters tell you the preset number
This shows the harmony control mode as either; Double, Scale, Chord or Notes. See
‘Harmony Control Modes’ for more information on page 10.
‘Harmony Control Modes’ for more information on page 10.
Following the Harmony Control Mode, information particular to the Harmony Control
Mode of the preset is shown.
Mode of the preset is shown.
Storing Presets
This is very simple. Anytime you make a change to a parameter which is stored by preset (levels,
rev., scale, voicing, etc.) the Store Button will light. If you want to write these changes to memo-
ry follow these steps:
rev., scale, voicing, etc.) the Store Button will light. If you want to write these changes to memo-
ry follow these steps:
1
2
3
With a microphone or line level source connected to VOCALIST VR, sing or play back a track. Bring
up the input level until the level LED lights orange. Too much input level, and the LED will be
red. Too little input level, and the LED will only light green, never lighting orange. If there are
momentary flickers of red, your signal level will remain clean.
up the input level until the level LED lights orange. Too much input level, and the LED will be
red. Too little input level, and the LED will only light green, never lighting orange. If there are
momentary flickers of red, your signal level will remain clean.
The only level setting you need to do on the output is with the output level switch on the back
panel of VOCALIST VR. This allows you to match VOCALIST VR’ output to the sensitivity of
your mixer input. When the switch is pushed in (-10dBu) VOCALIST VR is operating at line level.
When the switch is out (+4dBu) then VOCALIST VR will produce a higher level.
panel of VOCALIST VR. This allows you to match VOCALIST VR’ output to the sensitivity of
your mixer input. When the switch is pushed in (-10dBu) VOCALIST VR is operating at line level.
When the switch is out (+4dBu) then VOCALIST VR will produce a higher level.
note: generally this can be set at +4, but if your mixer is distorting, VOCALIST VR’ output level
should be reduced to -10dBu.
should be reduced to -10dBu.
The VOCALIST VR contains 50 factory presets. To select a preset use Data Entry Knob to
scroll through presets. The presets are loaded automatically as you scroll through them. Edited
presets can be saved over top of factory presets as user presets. See ‘Storing Presets’ for further
details. The LCD display shows preset information in the following way:
scroll through presets. The presets are loaded automatically as you scroll through them. Edited
presets can be saved over top of factory presets as user presets. See ‘Storing Presets’ for further
details. The LCD display shows preset information in the following way: