Hitachi 42pd9r10 Manual Do Utilizador
14
CONNECTION
Terminal Positions
Rear
Power Cord Socket
Aerial Socket
AV1
AV2
AV3
AV4
Monitor Out and Sub Woofer
Service use only
Power Swivel Terminal
Aerial Socket
AV1
AV2
AV3
AV4
Monitor Out and Sub Woofer
Service use only
Power Swivel Terminal
(See
51
)
PC Connection terminals
(D-sub 15 pin and mini stereo for
Audio)
Audio)
HDMI1, 2 and mini stereo for Audio
Common Interface slot
Common Interface slot
Side
AV5
Headphone terminal
Photo Input terminal
SD Memory Card slot
Headphone terminal
Photo Input terminal
SD Memory Card slot
Connecting Procedure
This unit is ready for various kinds of connections. Make a connection in the following steps. Be sure to turn off the
Main Power fi rst when connecting external equipments.
Main Power fi rst when connecting external equipments.
1. Connect Power Cord to the rear panel.
2. Connect Aerial Lead.
3. Connect your external equipments to the unit if any.
4. Connect the Power Plug to the Wall Socket.
2. Connect Aerial Lead.
3. Connect your external equipments to the unit if any.
4. Connect the Power Plug to the Wall Socket.
1. Connecting Power Cord to the Rear Panel
Connect Power Cord to the monitor.
*Make sure not to connect the Power Plug to the Wall Socket
until all connections are completed.
*Make sure not to connect the Power Plug to the Wall Socket
until all connections are completed.
2. Connecting Aerial Lead.
There are two ways to connect Aerial Lead.
When you do not have any other external equipment:
Connect the Aerial Lead directly into the Socket at rear panel.
When you have one or more external devices to connect:
1. Use RF cable to connect between each equipment and
Antenna.
2. Connect the Aerial Lead to an equipment‘In’Socket marked
3. Connect the RF cable from the equipment ‘Out’ to the other equipment ‘In.’
4. Then, connect from the equipment ‘Out’ to “ANT” on the plasma screen Socket on marked.
3. Connect the RF cable from the equipment ‘Out’ to the other equipment ‘In.’
4. Then, connect from the equipment ‘Out’ to “ANT” on the plasma screen Socket on marked.
VCR
STB
IN
OUT
IN
OUT
Digital
Analogue
OK
P
P
SD MEMORY
CARD
PUSH-EJECT
PH35814
INPUT(A
V5)
R
L/MONO
AUDIO
VIDEO
S-VIDEO
PH35826
Licensed by BBE Sound, Inc. under
one or more of the following US
patents : 5510752, 5736897.
BBE and BBE symbol are registered
trademarks of BBE Sound, Inc.
one or more of the following US
patents : 5510752, 5736897.
BBE and BBE symbol are registered
trademarks of BBE Sound, Inc.
WOW, SRS and symbol are
trademarks of SRS Labs, Inc.
trademarks of SRS Labs, Inc.
SERVICE USE ONLY
INPUT(RGB)
ANALOG RGB
INPUT(HDMI)
PC
AUDIO
AUDIO
A C
INPUT
(AV1)
INPUT
(AV2)
INPUT
(AV3)
INPUT
(AV4)
ANT
OUTPUT
AUDIO
VIDEO
SUB WOOFER
POWER SWIVEL
HDMI2
HDMI1
L
C
C
PR
PB
L
MONO R
R
Y/VIDEO
AUDIO
C.1
C.2
COMMON
INTERFACE
[Example: Connecting Antenna
through STB and VCR]
Precautions when connecting the aerial
Please use a coaxial cable which is free from interference to connect the aerial. Avoid using a parallel fl at feeder
wire as interference may occur, causing reception to be unstable and stripe noise to appear on the screen.
Avoid using indoor aerial as this may be affected by interference. Please use CATV net or outdoor aerial.
If noise appears in the picture of VHF-Low band channel, please use a double-shielded cable (not provided) for
If noise appears in the picture of VHF-Low band channel, please use a double-shielded cable (not provided) for
RF LEADS to reduce the noise.
NOTE
If analogue and digital broadcast signals are provided from the separated cables (antenna), please use a mixer
and RF cable to connect antenna terminal in order to receive both signals.