Hitachi 42pma400e Manual Do Utilizador
10
Anti-tumble measures
Securing to a wall or pillar
Using a commercially available cord,
chain and clamp, secure the set to a firm
wall or pillar.
chain and clamp, secure the set to a firm
wall or pillar.
Securing desktop
1)Using wood screws (two), fasten the set to the
clamping screw holes on the rear of the stand
as shown.
as shown.
2)Using commercially available wood screws,
secure the set firmly in position.
No stand is provided with this product. When installing the monitor,
use the optional Desk-top Stand (CMPAD05), Wall Mount Unit
(horizontal-mount CMPAK05, vertical/horizontal-mount CMPAK15),
or Ceiling Mount Unit (CMPAT05).
The Desk-top Stand has been used for the illustrations in this
manual.
use the optional Desk-top Stand (CMPAD05), Wall Mount Unit
(horizontal-mount CMPAK05, vertical/horizontal-mount CMPAK15),
or Ceiling Mount Unit (CMPAT05).
The Desk-top Stand has been used for the illustrations in this
manual.
Using the optional vertical-mount unit
(CMPAK15)
(CMPAK15)
Using the optional wall-mount unit (CMPAK15) allows set to mount
on wall surfaces as shown at below.
1) Make at least four sets of commercial anchor bolts and screws
on wall surfaces as shown at below.
1) Make at least four sets of commercial anchor bolts and screws
available to meet various kinds of walls to mount on.
2) Read the instructions supplied with the wall-mount unit carefully to
optimally locate the plasma display on a wall surface.
3) Prepare the wall surface for anchoring and drilling as needed, as
shown in the sketches.
• Make sure that an adequate wall surface strength and a screw
holding strength are available.
SPEAKER
TERMINAL
8 8W
SPEAKER
TERMINAL
8 8W
Horizontal mounting
Upper left vertical mounting
Plasma display outline
Wall surface
Anchor bolt
Hold to 25 mm
(1 inch) or below.
(1 inch) or below.
SPEAKER TERMINAL 8 8
W
SPEAKER TERMINAL 8 8
W
Driving anchor bolts into
a wall surface
a wall surface
Plasma display outline
Side view
INSTALLATION INSTRUCTIONS
Installation
• Installation of the wall mount unit and
ceiling mount unit can be dangerous, so
do not attempt this work yourself. Ask your
dealer to provide the name of a qualified
installer.
do not attempt this work yourself. Ask your
dealer to provide the name of a qualified
installer.
• In order to prevent an internal temperature
increase, maintain a space of 10cm (4
inches : For a desktop set-up) or more
between the sides and other objects such
as walls, etc., so that the ventilation holes
are not blocked.*
inches : For a desktop set-up) or more
between the sides and other objects such
as walls, etc., so that the ventilation holes
are not blocked.*
CAUTIONS
Have this unit mounted in a stable place. Take measures to
prevent it from tumbling down to avoid possible physical injury.
prevent it from tumbling down to avoid possible physical injury.
CAUTIONS
Horizontal mounting
Upper left vertical
mounting
mounting
Indicating lamp
The mounted unit should have the indicating lamp at its bottom.
Otherwise, an elevated internal temperature rise could cause the
unit to fail or fire.
Otherwise, an elevated internal temperature rise could cause the
unit to fail or fire.
CAUTIONS
Cord
or
chain
Clamp
10cm (4 inches) or more
*
Deux endroits
Vis bois
Cord
or
chain
Clamp
10cm (4 inches) or more
*
Use one of the special mount units to install this product. A mount
of insufficient strength or inadequate design can cause overturning
or dropping and result in fire, electrical shock or injury. Please
note that our company assumes absolutely no responsibility for
personal injuries or property damage caused by use of other
mount units or improper installation.
of insufficient strength or inadequate design can cause overturning
or dropping and result in fire, electrical shock or injury. Please
note that our company assumes absolutely no responsibility for
personal injuries or property damage caused by use of other
mount units or improper installation.
WARNING