games-microsoft-xbox steel battallion Manual Do Utilizador
2
3
CONTROLLER SETUP
PRECAUTIONS
•
Do not plug more than 2
STEEL BATTALION
controllers
into the same Xbox unit.
•
Do not touch the aiming lever or selection lever when
connecting the
connecting the
STEEL BATTALION
controller or turning
on the power.
•
When attaching
STEEL BATTALION
controller pieces, do
not mix up the left unit with the right unit. Be sure to attach
them in their correct positions.
them in their correct positions.
•
The
STEEL BATTALION
controller is made with small,
precision parts. Do not put anything on it or place it on an
unstable shelf.
unstable shelf.
•
Always turn the Xbox console off before removing the
STEEL
BATTALION
controller.
•
When cleaning the
STEEL BATTALION
controller, make
sure you turn the power off beforehand. Clean the controller
with a soft, dry towel. Do not use oil as it could cause fading or
possible deformation of the unit.
with a soft, dry towel. Do not use oil as it could cause fading or
possible deformation of the unit.
•
Do not drop the
STEEL BATTALION
controller.
•
Do not forcibly bend the cable, pull it out or place a heavy item
on it.
on it.
•
When removing the cable, make sure you hold the area that
attaches to the Xbox console to pull out the cable.
attaches to the Xbox console to pull out the cable.
•
Do not store the
STEEL BATTALION
controller in
locations subject to extreme heat or cold, or where water or
dampness could be present.
dampness could be present.
•
Use the
STEEL BATTALION
controller for its intended
purpose only.
TROUBLESHOOTING
Before sending the
STEEL BATTALION
controller out to be
repaired, please perform the following checks:
The controller does not respond –
•
Reconnect the controller from the beginning and restart the
machine.
machine.
The aiming lever LED light does not come on –
•
Move the shift lever over to a position where the LED will light
up. Leaving the lever in a position where it will not light up for
extended periods could cause the LED to stop lighting up.
up. Leaving the lever in a position where it will not light up for
extended periods could cause the LED to stop lighting up.
RIGHT UNIT ASSEMBLY
Warning: Do not mix up the right and left units. Make sure you
connect them in their correct positions.
connect them in their correct positions.
1.
Connect the centre unit and the right unit by inserting the
connector cable into the jacks in both units.
connector cable into the jacks in both units.
ATTENTION:
You must connect the cable end to the centre unit
in the correct position. Check the direction in which the cable
must be facing before attempting to plug it into the unit.
must be facing before attempting to plug it into the unit.
2.
Make sure you insert the connector cable ends all the way into
the jacks. Failure to do so could cause the controller not to
operate.
the jacks. Failure to do so could cause the controller not to
operate.
3.
Make sure the connector cable is not pinched between the two
units.
units.
WARNING: Pulling on the connector cable too roughly can
break the wires inside and make the unit unusable.
break the wires inside and make the unit unusable.
4. Firmly attach the connector unit cover. A small R or L is written
on the back of each connector unit cover. Use the R cover with
the right unit and the L cover with the left unit.
the right unit and the L cover with the left unit.
5.
Insert the screws into the four connector holes in the
connector unit cover. Use the Alan wrench attached to the
underside of the centre unit for this purpose.
connector unit cover. Use the Alan wrench attached to the
underside of the centre unit for this purpose.
6. Tighten the screws to finish.
LEFT UNIT ASSEMBLY
Follow the same steps as for connecting the right unit (above).
FULLY ASSEMBLED STEEL BATTALION CONTROLLER
STEEL BATTALION CONTROLLER ASSEMBLY
Connect the centre unit and the right unit by inserting the connector cable into the jacks in both units.
Make sure you insert the connector cable ends all the way into the jacks.
Firmly attach the connector unit cover.
Insert the screws into the four connector holes in the connector unit cover and tighten them.
A
B
C
D
E
F
G
H