Hanna Instruments hi 9063 Manual Do Utilizador
OPERATIONAL GUIDE
INITIAL PREPARATION
Each meter is supplied complete with
batteries.
Remove the back cover, unwrap the
batteries and install them while pay-
ing attention to their polarity.
Connect a K-type thermocouple probe to
the meter.
To switch on, press the ON/OFF key on
the front of the meter.
If the meter does not come on, make
sure that the batteries are correctly
installed.
The thermometer will carry out a self diagnostic test routine,
the LCD will show all segments for a few seconds (or as long as
ON/OFF is held), followed by the per-
centage indication of the remaining
battery life.
The thermometer then enters normal measurement mode.
If a temperature probe is plugged in, the meter displays the
measured temperature.
If no probe is plugged in, or if reading
is over-range, the display shows flash-
ing dashes.
If a measurement is slightly over the range of the meter
specifications, the display flashes the closest full-scale value.
To switch the thermometer OFF, press the ON/OFF key.
batteries.
Remove the back cover, unwrap the
batteries and install them while pay-
ing attention to their polarity.
Connect a K-type thermocouple probe to
the meter.
To switch on, press the ON/OFF key on
the front of the meter.
If the meter does not come on, make
sure that the batteries are correctly
installed.
The thermometer will carry out a self diagnostic test routine,
the LCD will show all segments for a few seconds (or as long as
ON/OFF is held), followed by the per-
centage indication of the remaining
battery life.
The thermometer then enters normal measurement mode.
If a temperature probe is plugged in, the meter displays the
measured temperature.
If no probe is plugged in, or if reading
is over-range, the display shows flash-
ing dashes.
If a measurement is slightly over the range of the meter
specifications, the display flashes the closest full-scale value.
To switch the thermometer OFF, press the ON/OFF key.
MEASURING SCALE (°C/°F)
The instrument is factory set to the °C scale, but measurements can
be performed in either the Celsius or Fahrenheit scale.
Press the °C/°F button to select the desired
scale.
be performed in either the Celsius or Fahrenheit scale.
Press the °C/°F button to select the desired
scale.
HOLD MODE
The HOLD function is activated by press-
ing the HOLD key.
The measured temperature is held on the
display until HOLD is pressed again.
The "H" tag blinks on the display to
indicate the HOLD mode.
Note: Although the display is frozen, internally the meter
ing the HOLD key.
The measured temperature is held on the
display until HOLD is pressed again.
The "H" tag blinks on the display to
indicate the HOLD mode.
Note: Although the display is frozen, internally the meter
continues measuring and updating Hi and Lo values.
BATTERY REPLACEMENT
HIGH/LOW TEMPERATURES
The maximum and minimum tempera-
tures are continuously monitored and
displayed in the lower portion of the
LCD.
Note: When reading goes over-range, the Hi and Lo values
tures are continuously monitored and
displayed in the lower portion of the
LCD.
Note: When reading goes over-range, the Hi and Lo values
display dashes until cleared.
CLEAR FUNCTION
Upon pressing the CLEAR key, the
current reading is assigned to the
highest and lowest temperature val-
ues. The High/Low values may be
cleared at any time during measure-
ment.
current reading is assigned to the
highest and lowest temperature val-
ues. The High/Low values may be
cleared at any time during measure-
ment.
ACCESSORIES
IST9063R1 06/05
Recommendations for Users
Before using this product, make sure that it is entirely suitable for the environment in which it is used.
Operation of this instrument in residential areas could cause unacceptable interference to radio and
TV equipment, requiring the operator to take all necessary steps to correct interference.
Any variation introduced by the user to the supplied equipment may degrade the instruments' EMC
performance.
To avoid electrical shock, do not use these instruments when voltage at the measurement surface
exceeds 24 Vac or 60 Vdc.
To avoid damage or burns, do not perform any measurement in microwave ovens.
Operation of this instrument in residential areas could cause unacceptable interference to radio and
TV equipment, requiring the operator to take all necessary steps to correct interference.
Any variation introduced by the user to the supplied equipment may degrade the instruments' EMC
performance.
To avoid electrical shock, do not use these instruments when voltage at the measurement surface
exceeds 24 Vac or 60 Vdc.
To avoid damage or burns, do not perform any measurement in microwave ovens.
CE DECLARATION OF CONFORMITY
The instrument is powered by four 1.5 V alkaline batteries
and is provided with the Battery Error Prevention System
(BEPS), which turns the unit off when a low battery signal is
detected.
When the remaining battery level is
less than 10%, a warning symbol
blinks on the display to indicate a low
battery condition.
It is recommended to replace the batteries as soon as the low
battery condition is detected.
Battery replacement must only take place in a nonhazardous
area using four 1.5V alkaline batteries.
In order to replace rundown batteries, simply remove the two
screws on the rear cover of the instrument and replace the
four batteries with new ones paying attention to the correct
polarity.
Reattach the cover and tighten the two screws.
and is provided with the Battery Error Prevention System
(BEPS), which turns the unit off when a low battery signal is
detected.
When the remaining battery level is
less than 10%, a warning symbol
blinks on the display to indicate a low
battery condition.
It is recommended to replace the batteries as soon as the low
battery condition is detected.
Battery replacement must only take place in a nonhazardous
area using four 1.5V alkaline batteries.
In order to replace rundown batteries, simply remove the two
screws on the rear cover of the instrument and replace the
four batteries with new ones paying attention to the correct
polarity.
Reattach the cover and tighten the two screws.
K-TYPE THERMOCOUPLE PROBES
with integral handle, 1 m (3.3’) cable & mini-connector:
HI 766A
HI 766A
Roller surface probe, max 320°C/600°F
HI 766B
Surface probe, max 650°C/1200°F
HI 766B1
90º Surface probe, max 450°C/840°F
HI 766B2
Spring-loaded, surface probe, max
900°C/1650°F
900°C/1650°F
HI 766B3
Spring-loaded, small surface probe with
insulated shaft, max 200°C/390°F
insulated shaft, max 200°C/390°F
HI 766C
Penetration probe, max 900°C/1650°F
HI 766C1
Ultra-fast Penetration probe, max 300°C/
570°F
570°F
HI 766D
Air probe, max 300°C/570°F
HI 766E1
General purpose probe, max 900°C/1650°F
HI 766E2
General purpose probe, max 900°C/1650°F
HI 766F
High temperature, flexible wire probe
without handle, max 1100°C/2000°F
without handle, max 1100°C/2000°F
HI 766F1
Flexible wire probe without handle, max
480°C/ 900°F
480°C/ 900°F
HI 766TR1
Penetration probe, max 250°C/482°F
HI 766TR2
Penetration long probe, max 250°C/482°F
HI 766TV1
Pipe clamp probe, max 200°C/390°F
with detachable handle & mini-connector
(to be used
in conjunction with the HI 766HD probe handle):
HI 766PA
Roller surface probe, max 320°C/600°F
HI 766PB
Surface probe, max 650°C/1200°F
HI 766PC
Penetration probe, max 900°C/1650°F
HI 766PD
Air probe, max 300°C/570°F
HI 766PE1
General purpose probe, max 900°C/1650°F
HI 766PE2
General purpose probe, max 900°C/1650°F
grill surface probe:
HI 766B4
HI 766B4
Grill surface probe with 70 cm (27.6’’)
cable (protected with stainless steel jacket),
max 250°C/482°F
cable (protected with stainless steel jacket),
max 250°C/482°F
HI 7664B4S
Spare stainless steel sensor for HI766B4 probe
OTHER ACCESSORIES
HI 710021
Spare protective case
HI 721317
Rugged carrying case
HI 766EX
Extension cable for K-type probes
HI 766HD
Rugged thermocouple probe handle with
1m (3.3') cable fitted with mini-connector
1m (3.3') cable fitted with mini-connector