Moxa ioLogik E1212 Guia De Especificação
Remote I/O
2
w w w. m o x a . c o m
ioLogik E1212 Specifications
ioLogik E1211 Specifications
ioLogik E1210 Specifications
Inputs and Outputs
Digital Inputs: 16 channels
Isolation: 3k VDC or 2k Vrms
Isolation: 3k VDC or 2k Vrms
Digital Input
Sensor Type: Wet Contact (NPN or PNP), Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Inputs and Outputs
Digital Outputs: 16 channels
Isolation: 3k VDC or 2k Vrms
Isolation: 3k VDC or 2k Vrms
Digital Output
Type: Sink
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 500 Hz
Over-Voltage Protection: 45 VDC
Over-Current Protection: 2.6 A (4 channels @ 650 mA)
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 500 Hz
Over-Voltage Protection: 45 VDC
Over-Current Protection: 2.6 A (4 channels @ 650 mA)
Inputs and Outputs
Digital Inputs: 8 channels
Configurable DIOs (by jumper): 8 channels
Isolation: 3k VDC or 2k Vrms
Configurable DIOs (by jumper): 8 channels
Isolation: 3k VDC or 2k Vrms
Digital Input
Sensor Type: Wet Contact (NPN or PNP), Dry Contact
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type: 8 points per COM
Counter Frequency: 250 Hz
Digital Filtering Time Interval: Software Configurable
I/O Mode: DI or Event Counter
Dry Contact:
• On: short to GND
• Off: open
Wet Contact (DI to COM):
• On: 10 to 30 VDC
• Off: 0 to 3 VDC
Common Type: 8 points per COM
Counter Frequency: 250 Hz
Digital Filtering Time Interval: Software Configurable
Common Type: 8 points per COM
Counter Frequency: 250 Hz
Digital Filtering Time Interval: Software configurable
Counter Frequency: 250 Hz
Digital Filtering Time Interval: Software configurable
Power Requirements
Input Voltage: 12 to 36 VDC
Input Current: 110 mA @ 24 VDC
Input Current: 110 mA @ 24 VDC
MTBF
(mean time between failures)
Time: 671,345 hrs
Standard: Telcordia SR332
Standard: Telcordia SR332
Over-Temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating: 200 mA per channel
Current Rating: 200 mA per channel
Power Requirements
Input Voltage: 12 to 36 VDC
Input Current: 200 mA @ 24 VDC
Input Current: 200 mA @ 24 VDC
MTBF
(mean time between failures)
Time: 923,027 hrs
Standard: Telcordia SR332
Standard: Telcordia SR332
Digital Output
Type: Sink
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 500 Hz
Over-Voltage Protection: 45 VDC
Over-Current Protection: 2.6 A (4 channels @ 650 mA)
Over-Temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating: 200 mA per channel
I/O Mode: DO or Pulse Output
Pulse Output Frequency: 500 Hz
Over-Voltage Protection: 45 VDC
Over-Current Protection: 2.6 A (4 channels @ 650 mA)
Over-Temperature Shutdown: 175°C (typical), 150°C (min.)
Current Rating: 200 mA per channel
Power Requirements
Input Voltage: 12 to 36 VDC
Input Current: 155 mA @ 24 VDC
Input Current: 155 mA @ 24 VDC
MTBF
(mean time between failures)
Time: 561,930 hrs
Standard: Telcordia SR332
Standard: Telcordia SR332
For Modbus devices that are controlled and
detected by fixed addresses, users need to
spend a vast amount of time researching
and verifying initial configurations. Users
need to locate each device’s networking
details, such as I/O channels or vendor-
defined addresses, to enable the initial or
start address of a SCADA system or PLC.
The ioLogik E1200, with user-definable
Modbus/TCP addressing, offers greater
flexibility, and setup is easy. Instead of
worrying about individual devices, users
simply configure the function and address
map to fit their needs.
detected by fixed addresses, users need to
spend a vast amount of time researching
and verifying initial configurations. Users
need to locate each device’s networking
details, such as I/O channels or vendor-
defined addresses, to enable the initial or
start address of a SCADA system or PLC.
The ioLogik E1200, with user-definable
Modbus/TCP addressing, offers greater
flexibility, and setup is easy. Instead of
worrying about individual devices, users
simply configure the function and address
map to fit their needs.
User-Definable Modbus/TCP Addressing for Painless Upgrading of Existing Systems