Panamax MB850 Manual Do Proprietário
4.
DEFINITIONS FOR ILLUMINATED LCD INDICATORS
TROUBLE SHOOTING
Problem
Full-time surge protection outlets stop
providing power to equipment. Circuit breaker
button is projecting from the side of the unit.
providing power to equipment. Circuit breaker
button is projecting from the side of the unit.
The UPS does not perform
expected runtime.
expected runtime.
The UPS will not turn on.
UPS Software Program is inactive
(all icons are gray).
(all icons are gray).
Solution
Turn the UPS off and unplug at least one piece of equipment. Wait 10 seconds, reset
the circuit breaker by depressing the button, and then turn the UPS on.
the circuit breaker by depressing the button, and then turn the UPS on.
Recharge the battery by leaving the UPS plugged in.
Contact Panamax about replacement batteries at www.panamax.com
Turn the UPS off. Wait 10 seconds and then turn the UPS on.
The unit must be connected to a 110/120v 60Hz outlet
Contact Panamax about replacement batteries at www.panamax.com
Contact Panamax at www.panamax.com
Connect the USB cable to the UPS unit and an open USB port on the back of the
computer. You must use the cable that came with the unit.
computer. You must use the cable that came with the unit.
Check the back of the computer for an additional USB port. Move the cable to this
port.
port.
Shutdown your computer and turn the UPS off. Wait 10 seconds and turn the UPS
back on. This should reset the unit.
back on. This should reset the unit.
Possible Cause
Circuit breaker has tripped due
to an overload.
to an overload.
Battery not fully charged.
Battery is slightly worn out.
The unit failed a self test.
The unit is not connected to an
AC outlet.
AC outlet.
The battery is worn out.
Mechanical problem.
The USB cable is not
connected.
connected.
The USB cable is connected to
the wrong port.
the wrong port.
The unit is not providing
battery power.
battery power.
TECHNICAL SPECIFICATIONS
Capacity.......................................................... 850VA / 510W
Input Voltage on Utility................................... 90V to 140V
Input Frequency.............................................. 60 Hz ± 3 Hz
On-Battery Output Voltage..............................120Vac ± 5%
Transfer Time.................................................. 4ms Typical
Max. Load for UPS Outlets............................. 850VA / 510W
Max. Load for Full-Time
Surge Protection outlets (9 Outlets)...............12 Amps
On-Battery Output Wave Form ...................... Simulated Sine Wave Form
Operating Temperature ................................. + 32°F to 95° F / 0° C to 35° C
Operating Relative Humidity........................... 0 to 95% NON-CONDENSING
Input Voltage on Utility................................... 90V to 140V
Input Frequency.............................................. 60 Hz ± 3 Hz
On-Battery Output Voltage..............................120Vac ± 5%
Transfer Time.................................................. 4ms Typical
Max. Load for UPS Outlets............................. 850VA / 510W
Max. Load for Full-Time
Surge Protection outlets (9 Outlets)...............12 Amps
On-Battery Output Wave Form ...................... Simulated Sine Wave Form
Operating Temperature ................................. + 32°F to 95° F / 0° C to 35° C
Operating Relative Humidity........................... 0 to 95% NON-CONDENSING
Size (L x W x H)..............................................10.24" x 4.33" x 8.70" 26.0 x 11.0 x 22.6cm
Net Weight .................................................... 15.8 lbs
Typical Battery Recharge Time....................... 8 hours typical from total discharge
Typical Battery Life.........................................3 to 6 years, depending on number of
discharge/recharge
Net Weight .................................................... 15.8 lbs
Typical Battery Recharge Time....................... 8 hours typical from total discharge
Typical Battery Life.........................................3 to 6 years, depending on number of
discharge/recharge
cycles
Battery Type................................................... Spill-proof, Maintenance-free, sealed lead-acid
Safety Approvals............................................ UL1778(UPS), cUL107., FCC/DoC Class B
Safety Approvals............................................ UL1778(UPS), cUL107., FCC/DoC Class B
ESTIMATED RUNTIME IN MINUTES
DLP TV (260 Watts)...............................................................6 Minutes
HD Gaming Console.............................................................12 Minutes
Satellite Receiver / Cable Box...............................................80 Minutes
Media Player.........................................................................80 Minutes
DVR / TiVo
®
........................................................................120 Minutes
Normal
Utility failure—The UPS is providing battery power to the battery power supplied outlets.
Utility failure—The UPS is providing battery power.The rapid beeps mean that the battery will run out of
charge within a few minutes.
charge within a few minutes.
Battery overload—Occurs in the battery power-supplied outlets. Turn off the UPS and unplug at least one
piece of equipment from the UPS. Wait 10 seconds, press the circuit breaker reset button, then turn the
UPS on.
piece of equipment from the UPS. Wait 10 seconds, press the circuit breaker reset button, then turn the
UPS on.
Electrical wiring fault—This means there’s a wiring problem within the utility AC power outlet. A wiring
problem could be a bad ground, missed ground, or reversed wiring. You should disconnect all equipment
from the outlet and have it checked by an electrician.
problem could be a bad ground, missed ground, or reversed wiring. You should disconnect all equipment
from the outlet and have it checked by an electrician.
Off
2 beeps per 30 seconds
Rapid beeps
Long Beeps
None
On
On
On
On
On
On
On / Off
On / Off
On / Off
On
INS00853 REV. A 10-08
POWER ON WIRING FAULT ALARM CONDITION