Asian Express Holdings Limited 1350-R Manual Do Utilizador

PROBLEM

POSSIBLE REASON

SOLUTION

1. Power switched off

1. Switch the ON/OFF switch to ON

NO POWER

2. Polarity is reversed

2. Make sure all batteries are installed

correctly (see diagram B)

3. Batteries may be dead

3. Replace batteries

1. Remote is switched off

1. Switch the ON/OFF switch to ON

Remote Not

2. Proton™ is switched off

2. Switch the ON/OFF switch to ON

Responding

3. Too windy

3. Windy conditions severly affect the

operation of the Proton™

4. The Remote light is flashing

4. Replace batteries

Drone Won’t

1. Rotor speed too slow

1. Push throttle lever forward

lift off

2. Drone not fully charged

2. Recharge your Proton™

Drone
Decsends

1. Moving the throttle too quickly

1. Control the throttle slower and

Too Fast

smoother

Drone Not

1. Gyroscopes not functioning

1. Turn on the Proton™ and

Responding

Reset the Gyros (see diagram L)

Loss of
Proton™

1. Drone is out of range of remote

1. Keep the drone within a 20

Control

meter radius of the remote

PROTON™ WARNING:

The Proton™ is designed for INDOOR or OUTDOOR flight. Proton™ ‘s blades revolve at high speeds and can

cause damage to the user, spectators and animals. Stand away from the Proton™ to reduce the risk of

getting into the flight path. Warn spectators that you will be flying your Proton™ so that they are aware of

its position. Before flight, inspect the rotor blades to make certain that the blades are securely fastened to

the Proton™.

WARNING!

• Choking/Cutting Hazard. Small Parts/Sharp Rotor Blades.

• Keep hands, hair and loose clothing away from the propeller when the power switch is turned to the

ON position.

• Turn off the transmitter and Proton™ power switches when not in use.

• The included charger is built specifically for the Proton™ Li-Poly battery. Do not use it to charge any

other battery.

• New alkaline batteries are recommended for maximum performance.

• Parental supervision recommended when flying Proton™

BATTERY WARNINGS

RECHARGEABLE BATTERY:

This Proton™ uses a Li-Poly rechargeable battery. If battery no longer stays charged, dispose of battery

properly according to local disposal requirements.

CONTROLLER BATTERIES:

Remote control requires 2 “AAA” batteries (not included). Please read the important battery safety warning

below.

• Do not mix alkaline, standard (carbon-zinc) and rechargeable batteries (Nickel Metal Hydride).

• Do not mix old and new batteries.

• Non-rechargeable batteries are not to be recharged.

• Rechargeable batteries are to be removed from the item before being charged (if removable).

• Rechargeable batteries are only to be charged under adult supervision.

• Exhausted batteries should be removed immediately and must be recycled or disposed of properly

according to state or local government ordinances and regulations.

• The supply terminals are not to be short-circuited.

• Only batteries of the same or equivalent type as recommended are to be used.

• Batteries are to be inserted with the correct polarity (see inside booklet for diagram).

• Do not dispose batteries in a fire - batteries may leak or explode.

CARE AND MAINTENANCE

• Always remove the batteries from the wireless 2.4G remote control when it is not being used for an

extended period of time.

• To clean, gently wipe the remote control and Proton™ with a clean damp cloth.

• Keep the toy away from direct heat or sunlight.

• Do not submerge the toy into water. This can damage the unit beyond repair.

• Parental guidance recommended when installing or replacing the batteries.

TROUBLESHOOTING YOUR PROTON™

FRONT

REAR

Diagram S

REPLACING THE PROPELLER BLADES

Your Proton™ propeller system is a precision instrument that may need repair or replacement from time

to time for optimal flight function. Crash landing from high-speed aerial flights may cause damage to your

Proton™’s propellers.
1. Proton™ have four blades, two gray propellers on the front, and two black propellers on the back

Please note that the blades and the Proton™ are labeled with an embossed A or B (see the diagram S).
2. When replacing the propeller blades, gently remove the blade from the rotor shaft. Make sure to match

both the color of the blade and the indication letter on the blade with the letter on the aircraft.
3. Replace the damaged blade with the correct blade.

Gray Blade Front Left = A

Gray Blade Front Right = B

Black Blade Back Left = B

Black Blade Back Right = A