Good Life LLC UP1621 Manual Do Utilizador
II – Quick Settings for Common Pests
Below you will find the recommended Strobe, Sound, Frequency, and Installation settings for several common pests and uses. If you do
not see your pest listed below or would like more detailed information please read Sections III – VIII in this manual.
Bats in Attic
Strobe: Constant
Sound: Ultra Constant
Frequency Dial: 6-8
To Install: Place in attic or where you suspect the bats are
entering the roof area.
Medium Sized Pests in Yard
Strobe: Constant or Off
Sound: Ultra Sensor / Constant
Frequency Dial: 2-8
Motion Sensor: Adjust to preference
To Install: Place near ground level for small pests. For larger
pests place at body level of pest
Squirrels / Raccoons in Attic
Strobe: Constant or Off
Sound: Ultra Constant
Frequency Dial: 3-6
Strobe: Constant or Off
Sound: Ultra Constant
Frequency Dial: 3-6
To Install: Place in attic or crawl space depending on location of
pest.
To Use for Personal Safety
Strobe: Sensor
Sound: Alarm Sensor
Volume: 40-100
Motion Sensor: Adjust to preference
To Install: Place near area you want to protect such as hallways,
doorways, yard areas, RVs, etc
pest.
To Use for Personal Safety
Strobe: Sensor
Sound: Alarm Sensor
Volume: 40-100
Motion Sensor: Adjust to preference
To Install: Place near area you want to protect such as hallways,
doorways, yard areas, RVs, etc
III -
Adjusting the Strobe Settings
I.
Sensor: The Strobe Light (A) will activate only when triggered by the
Motion Sensor (B)
Motion Sensor (B)
■
Best used to repel large pests that will easily set off the Motion
Sensor
Sensor
■
If you are using batteries, this setting conserves power compared
to the “Constant” setting
to the “Constant” setting
■
If the Strobe Light is set to “Sensor”, then the sound must be set to
either “Ultra Sensor” or “Alarm Sensor”
either “Ultra Sensor” or “Alarm Sensor”
II.
Off: The Strobe Light (A) is turned off.
■
Can be used with any sound setting.
III. Constant: The Strobe Light (A) will activate continuously.
■
Best used to repel small pests (such as insects) that will not be
detected by the Motion Sensor
detected by the Motion Sensor
■
If you are not sure exactly where the pests are located, this setting
may be easier for you to use than the Motion Sensor.
may be easier for you to use than the Motion Sensor.
■
If the Strobe Light is set to “Constant”, then the sound must also be
set to “Ultra Constant”.
set to “Ultra Constant”.
IV -
Adjusting the Sound Settings
I.
Ultra Sensor: The Speaker (C) will emit Ultrasonic Sound only when it
is activated by the Motion Sensor (B).
is activated by the Motion Sensor (B).
■
Best used to repel large pests that will easily set off the Motion
Sensor
Sensor
■
If you are using batteries, this setting conserves power compared
to the “Constant” setting
to the “Constant” setting
■
If the sound is set to “Ultra Sensor”, then the Strobe Light must also
be set to “Sensor” (or “Off”).
be set to “Sensor” (or “Off”).
I.
Ultra Constant: The Speaker (C) will emit Ultrasonic Sound
continuously.
continuously.
■
Best used to repel small pests (such as insects) that will not be
detected by the Motion Sensor
detected by the Motion Sensor
■
If you are not sure exactly where the pests are located, this setting
may be easier for you to use than the motion sensor.
may be easier for you to use than the motion sensor.
■
We recommend using the AC Adapter (H) with this setting
because the continuous sound will drain the batteries quickly.
because the continuous sound will drain the batteries quickly.
■
If the sound is set to “Ultra Constant”, then the Strobe Light must