Food Automation - Service Techniques Inc. XWIRE-SENSOR Manual Do Utilizador
2
© 2007-2008 SCK Direct, Inc. 229-51262 Rev B www.MySCK.com
SmartSensor
TM
Direct, Inc.
NOTICES
SCK Direct, Inc. is not liable for any use of product not in accor-
dance with SCK Direct, Inc.’s installation and operation
instructions.
dance with SCK Direct, Inc.’s installation and operation
instructions.
CLEANING
Using a clean damp cloth, wipe down the SmartSensor when
necessary using a commercial quality foodservice-approved
detergent. DO NOT IMMERSE.
necessary using a commercial quality foodservice-approved
detergent. DO NOT IMMERSE.
NEVER use chemical or abrasive cleaners on the SmartSensor.
TOOLS REQUIRED FOR INSTALLATION
Drill Bit: 3/16” if using wall anchor, or #50 if installing into
metal
metal
Phillips Screwdriver
INCLUDED PARTS
Please confirm that these parts have shipped with your order:
231-60232-01 SmartSensor
229-51362 Installation Manual
139-10029 Magnet
SmartSensor Mounting Kit
213-50641
213-50641
Magnet Mounting Kit
213-50758-01
213-50758-01
229-51364 MAC ID Identification
Fax Sheet
Fax Sheet
If something is missing, please call 1-866-840-4271 (8:00 a.m. -
5:00 p.m. EST).
5:00 p.m. EST).
BEFORE YOU INSTALL
SmartSensors should be installed after the installation of your
SCK Smart Direct 2
SCK Smart Direct 2
TM
, SCK Kitchen Advisor
TM
, or (FAST.) Xwire
TM
Wireless Gateway.
LOCATE YOUR MAC ID
Fill in the included form with your MAC ID numbers. The MAC ID
numbers are located on the back of the SmartSensors.
numbers are located on the back of the SmartSensors.
Before starting the installation, please fax the sheet immediately
to the SCK Helpdesk at +1 203-377-8187. This is necessary for
proper network setup by SCK Direct, Inc.
to the SCK Helpdesk at +1 203-377-8187. This is necessary for
proper network setup by SCK Direct, Inc.
INSTALLATION
WITHOUT
DOOR OPEN/CLOSE FEATURE
1a. Choose a location for the SmartSensor to be installed. Use
the SmartSensor mounting bracket as a template and mark
the locations of the 2 mounting holes.
the locations of the 2 mounting holes.
View the tentative positioning and ensure that there are no
location problems. Drill the 2 holes with the appropriate drill
bit as defined in Tools Required. Insert screws and mount
bracket.
location problems. Drill the 2 holes with the appropriate drill
bit as defined in Tools Required. Insert screws and mount
bracket.
Changes or modifications not expressly
approved by SCK Direct, Inc. could void the
user's authority to operate the equipment.
approved by SCK Direct, Inc. could void the
user's authority to operate the equipment.
NOTE: This equipment has been tested and found to comply
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
with the limits for a Class B digital device, pursuant to Part 15 of
the FCC Rules. These limits are designed to provide reasonable
protection against harmful interference in a residential installa-
tion. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance
with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interfer-
ence will not occur in a particular installation. If this equipment
does cause harmful interference to radio or television reception,
which can be determined by turning the equipment off and on,
the user is encouraged to try to correct the interference by one
or more of the following measures:
Reorient or relocate the receiving
antenna.
antenna.
Increase the separation between the equipment and
receiver.
receiver.
Connect the equipment into an outlet on a circuit different
from that to which the receiver is connected.
from that to which the receiver is connected.
Consult the dealer or an experienced radio/TV technician for
help.
help.