Food Automation - Service Techniques Inc. XWIRE-SENSOR Manual Do Utilizador
3
© 2007-2008 SCK Direct, Inc. 229-51262 Rev B www.MySCK.com
1b. If holes cannot be drilled, use supplied Velcro. Before
mounting, clean surface with an alcohol pad. Adhere one
side of Velcro to the mounting surface and one side of
Velcro to the back side of bracket.
side of Velcro to the mounting surface and one side of
Velcro to the back side of bracket.
2.
With the SmartSensor located within 10 feet of your SCK
Smart Direct 2, SCK Kitchen Advisor, or (FAST.) Xwire
Smart Direct 2, SCK Kitchen Advisor, or (FAST.) Xwire
TM
Wireless Gateway, wave the supplied magnet across the
embossed rectangle located on the bottom of the
SmartSensor at a maximum distance of .25” (6.35 mm).
Confirm the SmartSensor wakes up. You should see an LED
inside the SmartSensor flash for 10 seconds before turning
off. STORE MAGNET FOR FUTURE USE.
embossed rectangle located on the bottom of the
SmartSensor at a maximum distance of .25” (6.35 mm).
Confirm the SmartSensor wakes up. You should see an LED
inside the SmartSensor flash for 10 seconds before turning
off. STORE MAGNET FOR FUTURE USE.
NOTE: If the SmartSensor does not wake up, bring it close to
the SCK Smart Direct 2 so you can see the signal strength
indicator on the front. Wave magnet across the SmartSensor
again. If the SCK Smart Direct 2 lights flash, the SmartSensor
is already activated.
the SCK Smart Direct 2 so you can see the signal strength
indicator on the front. Wave magnet across the SmartSensor
again. If the SCK Smart Direct 2 lights flash, the SmartSensor
is already activated.
3a. Clip the SmartSensor into its bracket.
3b. Adhere SmartSensor assembly to mounting surface and
ensure it is secure.
4.
Your SmartSensor(s) will now be activated. Call the SCK
Helpdesk at 1-866-840-4271 (8:00 a.m. to 5:00 p.m. EST) to
confirm Sensors are on the network.
Helpdesk at 1-866-840-4271 (8:00 a.m. to 5:00 p.m. EST) to
confirm Sensors are on the network.
installation guide
INSTALLATION
WITH
DOOR OPEN/CLOSE FEATURE
INSTALLING THE SmartSensor
1a. The SmartSensor should be installed in the center of the
1a. The SmartSensor should be installed in the center of the
door opening at the top of the door frame. Use the
SmartSensor mounting bracket as a template and mark the
locations of the 2 mounting holes. Be sure to leave enough
room for the door to close.
SmartSensor mounting bracket as a template and mark the
locations of the 2 mounting holes. Be sure to leave enough
room for the door to close.
View the tentative positioning and ensure there are no loca-
tion problems. Drill the 2 holes with the appropriate drill bit
as defined in Tools Required. Insert screws and mount
bracket.
tion problems. Drill the 2 holes with the appropriate drill bit
as defined in Tools Required. Insert screws and mount
bracket.
1b. If holes cannot be drilled, use supplied Velcro. Before
mounting, clean surface with an alcohol pad. Adhere one
side of Velcro to the mounting surface and one side of
Velcro to the back side of bracket.
side of Velcro to the mounting surface and one side of
Velcro to the back side of bracket.
2.
With the SmartSensor located within 10 feet of your SCK
Smart Direct 2, SCK Kitchen Advisor, or (FAST.) Xwire
Smart Direct 2, SCK Kitchen Advisor, or (FAST.) Xwire
TM
Wireless Gateway, wave the supplied magnet across the
embossed rectangle located on the bottom of the
SmartSensor at a maximum distance of .25” (6.35 mm).
Confirm the SmartSensor wakes up. You should see an LED
inside the SmartSensor flash for 10 seconds before turning
off. STORE MAGNET FOR FUTURE USE.
embossed rectangle located on the bottom of the
SmartSensor at a maximum distance of .25” (6.35 mm).
Confirm the SmartSensor wakes up. You should see an LED
inside the SmartSensor flash for 10 seconds before turning
off. STORE MAGNET FOR FUTURE USE.
NOTE: If the SmartSensor does not wake up, bring it close to
the SCK Smart Direct 2 so you can see the signal strength
indicator on the front. Wave magnet across the SmartSensor
again. If the SCK Smart Direct 2 lights flash, the SmartSensor
is already activated.
the SCK Smart Direct 2 so you can see the signal strength
indicator on the front. Wave magnet across the SmartSensor
again. If the SCK Smart Direct 2 lights flash, the SmartSensor
is already activated.
3a. Clip the SmartSensor into its bracket.
3b. Adhere SmartSensor assembly to mounting surface and
ensure it is secure.
INSTALLING THE MAGNET
4.
4.
On the bottom side of the SmartSensor there is an
embossed rectangle. Line the magnet up with the rectangle.
embossed rectangle. Line the magnet up with the rectangle.
5a. Using the open end of this instruction manual as a gauge,
place the manual between the bottom of the SmartSensor
and the top of the magnet being sure to keep the magnet
aligned with the embossed rectangle. NOTE: The maximum
space allowed between the SmartSensor and top of
magnet is 0.25” (6.35 mm).
and the top of the magnet being sure to keep the magnet
aligned with the embossed rectangle. NOTE: The maximum
space allowed between the SmartSensor and top of
magnet is 0.25” (6.35 mm).
Use the magnet as a template and mark the locations of the
2 mounting holes. View the tentative positioning and
ensure there are no location problems. Drill the 2 holes with
the appropriate drill bit as defined in Tools Required. Insert
screws and mount magnet.
2 mounting holes. View the tentative positioning and
ensure there are no location problems. Drill the 2 holes with
the appropriate drill bit as defined in Tools Required. Insert
screws and mount magnet.
EMBOSSED
RECTANGLE
RECTANGLE
5b. If holes cannot be drilled, use supplied Velcro. Before
mounting, clean surface with an alcohol pad. Adhere one
side of Velcro to the mounting surface and one side of
Velcro to the magnet.
side of Velcro to the mounting surface and one side of
Velcro to the magnet.
6.
Your SmartSensor will now be activated. Call the SCK
Helpdesk at 1-866-840-4271 (8:00 a.m. to 5:00 p.m. EST) to
confirm Sensors are on the network.
Helpdesk at 1-866-840-4271 (8:00 a.m. to 5:00 p.m. EST) to
confirm Sensors are on the network.