Hewlett Packard Enterprise Company APINH103 Manual Do Utilizador

Installation Guide

www.arubanetworks.com

1344 Crossman Avenue

Sunnyvale, California 94089

Phone: 408.227.4500
Fax 408.227.4550

Aruba AP-103H Wireless Access Point | Installation Guide
Part Number 0511618-01 | April 2014

Main Site

Support Site

Airheads Social Forums and Knowledge Base

North American Telephone

1-800-943-4526 (Toll Free)

1-408-754-1200

International Telephones

Software Licensing Site

Wireless Security Incident
Response Team (WSIRT)

Americas and APAC

EMEA

emea.support@arubanetworks.com

Americas and APAC Support Email

WSIRT Email
Please email details of any security
problem found in an Aruba product.

© 2014 Aruba Networks, Inc.  AirWave

®

, Aruba Networks

®

, Aruba Mobility Management System

®

, Bluescanner, 

For Wireless That Works

®

, Mobile Edge Architecture, People Move. Networks Must Follow., RFProtect

®

, The All 

Wireless Workplace Is Now Open For Business, and The Mobile Edge Company

®

 are trademarks of Aruba 

Networks, Inc. All rights reserved. All other trademarks are the property of their respective owners.

Certain Aruba products include Open Source software code developed by third parties, including software code 
subject to the GNU General Public License ("GPL"), GNU Lesser General Public License ("LGPL"), or other Open 
Source Licenses. The Open Source code used can be found at this site:

http://www.arubanetworks.com/open_source

The use of Aruba Networks, Inc. switching platforms and software, by all individuals or corporations, to terminate 
other vendors' VPN client devices constitutes complete acceptance of liability by that individual or corporation for 
this action and indemnifies, in full, Aruba Networks, Inc. from any and all legal actions that might be taken against 
it with respect to infringement of copyright on behalf of those vendors.

This hardware product is protected by the standard Aruba warranty of one year parts/labor. For more information, 
refer to the ARUBACARE SERVICE AND SUPPORT TERMS AND CONDITIONS.

Altering this device (such as painting it) voids the warranty.

2. Remove any existing RJ45 connectors (typically snap-in) or cut/remove the 

UTP cable.

3. Use two short Ethernet cables (sold separately) to connect the AP to the RJ45 

connectors or crimp an RJ45 plug (not supplied) on the cable (or both cables 

if using the pass through).

4. Align the mounting holes of the AP-103H mounting bracket with mounting 

holes in you gang box as shown in 

Figure 7  Bracket to Gang Box (Standard US Single Gang Outlet Box Shown)

5. Connect any required cables to the rear of the AP-103H.

6. Align the mounting posts on the back of your AP-103H with the corresponding 

mounting holes on the mounting bracket as shown in 

.

7. Push the AP against the holes and downward until the posts engage the slots 

at the top of the mounting holes. 

Figure 8  AP-103H to Bracket

8. To remove the AP-103H from the mounting bracket, begin by inserting the 

enclosed security key into the hole.

9. Use the security key to depress the tab on the AP and push the AP up, 

releasing the AP from the mounting holes on the bracket.

10. If not using PoE, connect the AC-DC power adapter (sold separately) to the 

DC power socket located on the bottom of the AP-103H.

The integrated LED on the AP can be used to verify that the AP is receiving 
power and initializing successfully (see 

Table 1

). Refer to the 

Start Guide for further details on verifying post-installation network 
connectivity.

Provisioning parameters are unique to each AP. These local AP parameters are initially configured on 
the controller which are then pushed out to the AP and stored on the AP itself. Aruba recommends 
that provisioning settings be configured via the ArubaOS Web UI only. Refer to the 

Guide for complete details.

Configuration parameters are network or controller specific and are configured and stored on the 
controller. Network configuration settings are pushed out to the AP(s) but remain stored on the 
controller.

Configuration settings can be configured via the ArubaOS Web UI or ArubaOS CLI. Refer to 

User Guide for details.



Ethernet: 



1 x 10/100/1000Base-T auto-sensing Ethernet RJ-45 Interface (ENET 0)



2 x 10/100Base-T auto-sensing Ethernet RJ-45 Interfaces (ENET 1)



MDI/MDX



IEEE 802.3 (10Base-T), IEEE 802.3u (100Base-T). IEEE 802.3ab (1000Base-T)



Power over Ethernet (IEEE 802.3af compliant), 48V DC (nominal) and 56V DC (maximum)/
350mA (see 



Power:



12 VDC power interface, supports powering through an AC-to-DC power adapter



POE support on Ethernet ports: 802.3af-compliant POE sourcing device

For additional specifications on this product, please refer to the data sheet. The data sheet can be 
found at 

www.arubanetworks.com

.

For the most current information about Global Environmental Compliance and Aruba products, see 
our website at 

www.arubanetworks.com

.

Aruba products at end of life are subject to separate collection and treatment in 

the EU Member States, Norway, and Switzerland and therefore are marked with 

the symbol shown at the left (crossed-out wheelie bin). The treatment applied at 

end of life of these products in these countries shall comply with the applicable 

national laws of countries implementing Directive 2002/96EC on Waste of 

Electrical and Electronic Equipment (WEEE).

This product complies with RoHS requirements as prescribed by E-Waste (Management & Handling) 
Rules, governed by the Ministry of Environment & Forests, Government of India.

Aruba products also comply with the EU Restriction of Hazardous 

Substances Directive 2011/65/EC (RoHS). EU RoHS restricts the use of 

specific hazardous materials in the manufacture of electrical and 

electronic equipment. Specifically, restricted materials under the RoHS 

Directive are Lead (including Solder used in printed circuit assemblies), Cadmium, Mercury, 

Hexavalent Chromium, and Bromine. Some Aruba products are subject to the exemptions listed in 

RoHS Directive Annex 7 (Lead in solder used in printed circuit assemblies). Products and packaging 

will be marked with the “RoHS” label shown at the left indicating conformance to this Directive

.

Aruba products also comply with China environmental declaration requirements 
and are labeled with the “EFUP 25” label shown at the left.

Aruba Networks provides a multi-language document that contains country-specific restrictions and 
additional safety and regulatory information for all Aruba access points. This document can be 
viewed or downloaded from the following location: 

www.arubanetworks.com/safety_addendum

 

The following regulatory model name applies to the AP-103H:



AP-103H: APINH103

This device is electronically labeled. To view the FCC ID:

1.

Log into the controller WebUI.

Navigate to 

Maintenance > Controller > About.

This equipment generates, uses and can radiate radio frequency energy, and, if not installed and used 
in accordance with the manufacturer’s instructions may cause harmful interference to other devices 
in the vicinity. However, there is no guarantee that interference will not occur in a particular 
installation. If this equipment causes interference with other devices, which may be determined by 

turning the equipment off and on, the user is encouraged to try and correct the interference by one or 
more of the following measures:



Reorient or relocate the device receiving the interference.



Increase the separation between the equipment.



Connect the equipment into an outlet on a circuit different from that to which the other device(s) 
are connected.



Consult the manufacturer or field service technician for help.

The protection against electric shock is Class ll. 

Equipment not suitable for use in the presence of flammable mixtures.

This device complies with Part 15 of the Federal Communications Commission (FCC) Rules. 
Operation is subject to the following two conditions:

1.

This device may not cause harmful interference.

2.

This device must accept any interference received, including interference that may cause 
undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, 
pursuant to Part 15 of the FCC Rules. This equipment generates, uses and can radiate radio frequency 
energy and, if not installed and used in accordance with the manufacturer’s instructions, may cause 
interference harmful to radio communications.

If this equipment does cause interference, which can be determined by turning the equipment off and 
on, the user is encouraged to try to correct the interference by one or more of the following measures:



Reorient or relocate the receiving antenna.



Increase the separation between the equipment and receiver.



Connect the equipment to an outlet on a circuit different from that to which the receiver is 
connected.



Consult the dealer or an experienced radio or TV technician for help.

Complies with the Class B limits for radio noise emissions as set out in the interference-causing 
equipment standard entitled “Digital Apparatus,” ICES-003 of Industry Canada.

Cet apareil numerique de la classe B respecte toutes les exigencies du Reglement sur le materiel 
brouilleur du Canada.

Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz 
and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt 
WLAN devices.

This product is CE marked according to the provisions of the R & TTE Directive 
(1999/5/EC) - CE(!). Aruba Networks Inc., hereby declares that the APIN0103 device 

model is in compliance with the essential requirements and other relevant provisions of Directive 
1999/5/EC -CE(!)

The Declaration of Conformity made under Directive 1999/5/EC is available for viewing at the 
following location: 

Users are advised that high power Radars are allocated as primary users of the bands 5250-5350 MHz 
and 5650-5850 MHz and these Radars could cause interference and/or damage to Licensed Exempt 
WLAN devices.

Under Industry Canada regulations, this radio transmitter may only operate using an antenna of a 
type and maximum (or lesser) gain approved for the transmitter by Industry Canada. To reduce 
potential radio interference to other users, the antenna type and its gain should be so chosen that the 
equivalent isotropically radiated power (e.i.r.p.) is not more than that necessary for successful 
communication.

This device complies with Industry Canada licence-exempt RSS standard(s).

Operation is subject to the following two conditions: (1) this device may not cause interference, and 

(2) this device must accept any interference, including interference that may cause undesired 

operation of the device. 

If a power adapter other than the one provided by Aruba Networks is used 
in the US or Canada, it should be NRTL Listed, with an output rated 12 
VDC, minimum 1.25A, marked “LPS” or “Class 2,” and suitable for plugging 
into a standard power receptacle in the US and Canada.

Aruba access points must be installed by a professional installer. The 
professional installer is responsible for ensuring that grounding is available 
and it meets applicable local and national electrical codes.

Changes or modifications to this unit not expressly approved by the party 
responsible for compliance could void the user’s authority to operate this 
equipment.

RF Radiation Exposure Statement: This equipment complies with FCC 
RF radiation exposure limits. This equipment should be installed and 
operated with a minimum distance of 7.87 inches (20cm) between the 
radiator and your body for 2.4 GHz and 5 GHz operations. This transmitter 
must not be co-located or operating in conjunction with any other antenna 
or transmitter.