Tyco Safety Products/Sensormatic AMB9020 Manual Do Utilizador
Preliminary 2003-11-21
DUAL ANTENNA SCANMAX PRO DEACTIVATOR CONTROLLER
8200-0365-01, REV. 1A
INSTALLATION AND SERVICE GUIDE
2 of 12
About the Product
Product Overview
The Dual Antenna Deactivator controller supports
any two ScanMax Pro deactivation antennas used
to deactivate USII and USIII labels. A universal
input, 22Vdc output power supply powers the
controller.
The controller contains the necessary ports for:
• Wireless synchronization
• Network communication
• Maintaining independent antenna status
• Functional control for each antenna.
The controller also has:
• Automatic antenna type detection, except if
any two ScanMax Pro deactivation antennas used
to deactivate USII and USIII labels. A universal
input, 22Vdc output power supply powers the
controller.
The controller contains the necessary ports for:
• Wireless synchronization
• Network communication
• Maintaining independent antenna status
• Functional control for each antenna.
The controller also has:
• Automatic antenna type detection, except if
using the optional extension cable.
• Auto synchronization
• Automatic key switch detection
• Panel button for Label type (SR or DR) and
• Automatic key switch detection
• Panel button for Label type (SR or DR) and
power level (Full or Magnetic Media Safe)
• LEDs that indicate power on, communication
activity, and diagnostics.
Product Limitations
• The controller has max duty cycle of three
times a second.
• Both antennas must have the same power
level and label type
• Max throughput speed of 203cm/sec
(80”/second) unless otherwise limited by the
antenna.
antenna.
• Maximum distance between antenna and
controller is expected to be 3m (9.8ft), or 6m
(19.7ft) when optional extension cable 0652-
0136-01 is used.
(19.7ft) when optional extension cable 0652-
0136-01 is used.
• Antennas cannot deactivate simultaneously.
• No independent antenna power selection
• No independent antenna power selection
(both antennas full or MMS)
• No independent antenna label selection
(both antennas same label setting)
• Low Profile Pad and PowerPad have a 10%
reduction in deactivation height.
Magnetic Media Safe Operation
Magnetic Media Safe (MMS) operation enables
security labels in audiotapes and videotapes to be
deactivated without affecting the media. MMS is
selectable using a software configurator, or using
the push button on the controller.
security labels in audiotapes and videotapes to be
deactivated without affecting the media. MMS is
selectable using a software configurator, or using
the push button on the controller.
Synchronization
Auto-synchronization. Auto-synchronization
within the controller helps minimize tuning and
adjustment service calls. The controller
synchronizes to the antenna picking up the highest
in-band amplitude or to a wireless synchronization
input.
Wireless synchronization. The wireless
synchronization module plugs into the RS485 port
on the controller. If the TSP/Sensormatic network
is using this port, the module can be plugged into
the modular jack of the network terminal block
assembly.
within the controller helps minimize tuning and
adjustment service calls. The controller
synchronizes to the antenna picking up the highest
in-band amplitude or to a wireless synchronization
input.
Wireless synchronization. The wireless
synchronization module plugs into the RS485 port
on the controller. If the TSP/Sensormatic network
is using this port, the module can be plugged into
the modular jack of the network terminal block
assembly.
About the Controller
The controller consists of an aluminum and plastic
enclosure that contains power and control
electronics. All connections are made to a
connector plate on one side of the unit.
Connections include:
• DC power in
• Two deactivation outputs
• Two remote indicator ports
• Two RS232 ports: POS 1 and POS 2 (the
enclosure that contains power and control
electronics. All connections are made to a
connector plate on one side of the unit.
Connections include:
• DC power in
• Two deactivation outputs
• Two remote indicator ports
• Two RS232 ports: POS 1 and POS 2 (the
service configurator uses only the POS 1 port)
• Two Scan I/O ports
• RS485 port.
• RS485 port.
Connector Panel
Antenna 1
Antenna 2
Remote 1
Remote 2
LED for mag media safe (MMS)
LED for label type (SR)
Button: PROG
Control LED: Status 1 and Status 2
POS1/SERV
POS2
RS485
Scan IO 1
Scan IO 2
Antenna 1
Antenna 2
Remote 1
Remote 2
LED for mag media safe (MMS)
LED for label type (SR)
Button: PROG
Control LED: Status 1 and Status 2
POS1/SERV
POS2
RS485
Scan IO 1
Scan IO 2