Tyco Safety Products/Sensormatic AMB9020 Manual Do Utilizador
Preliminary 2003-11-21
DUAL ANTENNA SCANMAX PRO DEACTIVATOR CONTROLLER
8200-0365-01, REV. 1A
INSTALLATION AND SERVICE GUIDE
4 of 12
POS Integration
Scan I/O Port
POS integration uses the Scan I/O port and/or an
RS232 port. Scan I/O ports can be configured to
accept specific operating voltage levels to control
the deactivator. It will be compatible with the
AcoustoLink and Footlink options.
RS232 port. Scan I/O ports can be configured to
accept specific operating voltage levels to control
the deactivator. It will be compatible with the
AcoustoLink and Footlink options.
SCAN I/O Port Electrical Specifications
Maximum input voltage: +25Vdc ±5%
Input 1+ and Input 2+:
- Input voltage: 5–20Vdc positive or negative
Maximum input voltage: +25Vdc ±5%
Input 1+ and Input 2+:
- Input voltage: 5–20Vdc positive or negative
polarity, >20–25Vdc positive polarity only
- Current: 10mA source minimum
- Minimum pulse duration: 100ms.
Detect Out: open-collector side of an opto-isolator
- Maximum pull-up voltage: +25Vdc
- This output remains in the open state until a
- Minimum pulse duration: 100ms.
Detect Out: open-collector side of an opto-isolator
- Maximum pull-up voltage: +25Vdc
- This output remains in the open state until a
deactivation occurs. It then shorts to the Detect
Common for a minimum of 50ms based on label
vicinity to the antenna verse deactivation time.
Common for a minimum of 50ms based on label
vicinity to the antenna verse deactivation time.
Detect common: Emitter side of the Detect Out
opto-isolator normally should be tied to a ground
return. Maximum Current limit: 60mA.
opto-isolator normally should be tied to a ground
return. Maximum Current limit: 60mA.
Networking
The RS232 ports, if not used by a scanner
interface device or other auxiliary control device,
can be used for communicating to the customer
checkout register. The controller has a 6-position
modular jack (RJ11) that is the input/output for the
TSP/Sensormatic RS485 network. Information from
the register, when addressed correctly, passes
through the controller RS232 interface, to the
RS485 network, and on to its intended recipient.
To connect from the controller RS485 to
peripherals, such as an exit EAS system or tag
detacher, an optional interface assembly is
required. This assembly contains two 3 position
terminal blocks, two six-position modular jacks
(RJ11), and an input modular jack. The length of
the input cable from the controller to the networking
terminal block is determined by the baud rate and
line capacitance.
interface device or other auxiliary control device,
can be used for communicating to the customer
checkout register. The controller has a 6-position
modular jack (RJ11) that is the input/output for the
TSP/Sensormatic RS485 network. Information from
the register, when addressed correctly, passes
through the controller RS232 interface, to the
RS485 network, and on to its intended recipient.
To connect from the controller RS485 to
peripherals, such as an exit EAS system or tag
detacher, an optional interface assembly is
required. This assembly contains two 3 position
terminal blocks, two six-position modular jacks
(RJ11), and an input modular jack. The length of
the input cable from the controller to the networking
terminal block is determined by the baud rate and
line capacitance.
Interconnection Cables
The 183cm (6ft) power cord attaches to the
external power supply and into a 4-position mini-
din on the controller. The cord option selected
depends upon destination.
external power supply and into a 4-position mini-
din on the controller. The cord option selected
depends upon destination.
Cable length of SMPRO antennas is 3m (9.8ft).
The extension cable is 3m (9.8ft) long.
The extension cable is 3m (9.8ft) long.