N. V. Nederlandsche Apparatenfabriek NEDAP SENSITEPL Manual Do Utilizador
SENSIT SYSTEM | MANUAL
Mounting The SENSIT IR
41/92
8.6
INSTALLATION PROCEDURE
Below the mounting procedure for the SENSIT
sensor
.
SENSIT sensor mounting procedure
Step 1:
Preparation
Preparation
Indicate on the closed parking lot where the
SENSIT sensor should be mounted. Distribute
the SENSIT sensors over the parking lot and
write down the correct ID numbers on your
installation plan.
SENSIT sensor should be mounted. Distribute
the SENSIT sensors over the parking lot and
write down the correct ID numbers on your
installation plan.
Step 2:
Drilling
Drill a hole of Ø 85 mm [
3.35 in]
and at least 55
mm [2.16 in] deep into the centre of the parking
bay
bay
Step 3:
Gluing
Gluing
Apply the right amount of filler and pour into the
hole.
hole.
Step 4:
Mounting
Mounting
Double-check the node ID number and the
parking bay on the installation plan and place the
SENSIT sensor into the hole.
parking bay on the installation plan and place the
SENSIT sensor into the hole.
Step 5:
Cleaning-up
Cleaning-up
After mounting the SENSIT sensors in all parking
bays or a selection of parking bays. Clean up the
parking bays and remove all (metal) tools and
objects.
bays or a selection of parking bays. Clean up the
parking bays and remove all (metal) tools and
objects.
Step 6:
Activating
Activating
All SENSIT sensors are set into transport/stock
mode during shipment. After installation all
mounted SENSIT sensors must be swept with
the reset magnet.
mode during shipment. After installation all
mounted SENSIT sensors must be swept with
the reset magnet.
Step 7:
Calibrating
Calibrating
After installation the SENSIT sensor must be
calibrated. Ensure that the parking space is
empty and that there is no car parked on top of
the sensor or on neighboring parking bays.
SENSIT sensors can be calibrated via the SENIST
Interface Software (SIS). See chapter 13.6.6 for
more information about calibration.
calibrated. Ensure that the parking space is
empty and that there is no car parked on top of
the sensor or on neighboring parking bays.
SENSIT sensors can be calibrated via the SENIST
Interface Software (SIS). See chapter 13.6.6 for
more information about calibration.
Step 8:
Glue curing
Glue curing
Leave the filler harden for 8 hours before
vehicles are allowed in the parking space again.
vehicles are allowed in the parking space again.
8.7
REPLACEMENT
When the battery life of the SENSIT IR fails after specified lifetime, we advise to replace the
unit completely. The SENSIT IR is fully sealed and for outdoor use, therefore batteries
cannot be replaced.
Drill out the old SENSIT IR and complete the mounting procedure as describe in the
previous paragraph.
Ensure to note the node ID number of the SENSIT IR to the parking bay. Update the parking
bay configuration list in the SIS software to ensure the new sensor is linked to the right
parking bay.
unit completely. The SENSIT IR is fully sealed and for outdoor use, therefore batteries
cannot be replaced.
Drill out the old SENSIT IR and complete the mounting procedure as describe in the
previous paragraph.
Ensure to note the node ID number of the SENSIT IR to the parking bay. Update the parking
bay configuration list in the SIS software to ensure the new sensor is linked to the right
parking bay.
Note
Take attention that you fixate
the SENSIT sensor during the
curing time otherwise the
sensor will start to float.
Note
Once out of the
transport/stock mode the
battery lifetime starts to
count.
Note
When the SENSIT sensors are
not calibrated they hardly
send any messages. This is
due to the fact that there are
no events generated because
the magnetic thresholds are
not crossed.
Take attention that you fixate
the SENSIT sensor during the
curing time otherwise the
sensor will start to float.
Note
Once out of the
transport/stock mode the
battery lifetime starts to
count.
Note
When the SENSIT sensors are
not calibrated they hardly
send any messages. This is
due to the fact that there are
no events generated because
the magnetic thresholds are
not crossed.