NBS Payment Solutions Inc. NOIRE510W Manual Do Utilizador
Installation
The
510W short range wireless POS
terminals requires the installation of a
010 Wireless Base Station. The
base station can handle multiple POS
terminals. Larger locations may require
optional wireless signal repeaters to ensure
there is sufficient radio coverage in the
location.
terminals. Larger locations may require
optional wireless signal repeaters to ensure
there is sufficient radio coverage in the
location.
A-
510W POS
Terminal
Carefully preserve the packaging of the
terminal. It must be re-used whenever the
terminal is shipped.
THE
terminal. It must be re-used whenever the
terminal is shipped.
THE
510W PACKAGING
CONTAINS:
• The terminal itself, equipped with its
paper roll.
• Detachable power supply unit. (The
power supply unit delivered with your
terminal is specially designed for it. Do
not use any other power supply.) The use
of a power supply having apparently
similar voltage/current characteristics
may, in spite of this, damage your
terminal.
terminal is specially designed for it. Do
not use any other power supply.) The use
of a power supply having apparently
similar voltage/current characteristics
may, in spite of this, damage your
terminal.
• Battery.
• Installation Guide.
• Optional charging Base.
To power down the
510W:
•
Disconnect the power supply block
from the electric power supply
network.
from the electric power supply
network.
•
Press and hold the
key until
the display shuts off.
CHARGING THE
510W:
Select an electrical socket that complies with
the general safety instructions as outlined in
“Safety Instructions.”
Connecting the Power Supply to the
Optional Charging Base
the general safety instructions as outlined in
“Safety Instructions.”
Connecting the Power Supply to the
Optional Charging Base
•
Insert the small
connecter on the
power supply
cable into the
socket at the
back of the
optional charging
base.
connecter on the
power supply
cable into the
socket at the
back of the
optional charging
base.
•
To charge the terminal, gently place the
terminal on to the charging base.
terminal on to the charging base.
Connecting the Power Supply directly to
the
510W
•
Insert the small
connector on
the power
supply cable
with the
triangle facing
up, in to the
centre socket
on the back of the
connector on
the power
supply cable
with the
triangle facing
up, in to the
centre socket
on the back of the
510W
terminal
•
The terminal will automatically power on
and start to charge.
and start to charge.
To decrease the charging time, the terminal
may be powered off by pressing the
key until the display shuts off.
INSTALLING A ROLL OF PAPER
•
Depress the
printer door
release
button (see
arrow) to
disengage
the paper
door from the terminal.
printer door
release
button (see
arrow) to
disengage
the paper
door from the terminal.
•
Tilt the paper door towards the rear of
the terminal.
the terminal.
•
Remove and discard the empty paper
roll.
roll.
•
Verify that the roller is intact and
securely attached to the paper door.
securely attached to the paper door.
•
Install the paper
roll (thermally
coated side
exposed when
viewed from top)
into the
compartment.
The thermally sensitive side will create
black marks when it is scratched.
roll (thermally
coated side
exposed when
viewed from top)
into the
compartment.
The thermally sensitive side will create
black marks when it is scratched.
•
Tilt the paper door towards the front of
the terminal until resistance is felt.
the terminal until resistance is felt.
•
Press down on both corners of the paper
door until it clicks into position.
door until it clicks into position.
The
510W terminal is now ready
for use.
B-
010 Base Station
/ Repeater
The
010 Packaging contains:
• The wireless Base Station / Repeater
itself
•
Wireless antenna
•
Detachable power supply unit. (The
power supply unit is specially designed
for it. Do not use any other power
supply.)
power supply unit is specially designed
for it. Do not use any other power
supply.)
Connecting the
010 to the
Internet
The merchant is responsible for providing an
Internet connection with DHCP capabilities.
Connect an Ethernet cable from merchant
supplied device to the port marked
WAN/LAN on the
The merchant is responsible for providing an
Internet connection with DHCP capabilities.
Connect an Ethernet cable from merchant
supplied device to the port marked
WAN/LAN on the
010 base station.
Note: In large locations, an optional
010 configured as a wireless
repeater may be required. The wireless
repeater does NOT require an Internet
connection.
repeater does NOT require an Internet
connection.