NBS Payment Solutions Inc. NOIRE510W Manual Do Utilizador
C-Associating the Terminal
to the Base Station
to the Base Station
Setting up the Network
The network must be setup before
initializing the terminal.
1.
Go to the Service menu option
2.
Select the WLAN Configuration menu
option
3.
Select Setup New Network
4.
Make sure all base stations and
repeaters are unplugged.
5.
Enter the terminal ID (pressing the
button labelled with the
character/number will bring up a screen
for the input selection/confirmation).
character/number will bring up a screen
for the input selection/confirmation).
6.
Follow the instructions on the terminal.
Verifying the ESSID of the Base Station
To verify the terminal is connecting to a
base station:
1.
Go to the Service menu option
2.
Select the WLAN Configuration menu
option
3.
Select WLAN Survey
4.
The Base Station ESSID, the MAC
address and the signal strength of the
terminal will be displayed.
terminal will be displayed.
Resetting the Base Station
There is a small Reset button located on the
back of the Base Station.
1.
To reset the Base Station without
changing the existing ESSID:
While the Base Station is powered on,
pressing down the reset button and then
release it.
2.
pressing down the reset button and then
release it.
2.
To reset the Base Station to the default
ESSID:
While the Base Station is powered on,
pressing down the reset button and hold the
press for 10 seconds and then release it.
pressing down the reset button and hold the
press for 10 seconds and then release it.
Resetting the Terminal’s WLAN
Configuration
Configuration
1.
Go to the Service menu option
2.
Select the WLAN Configuration menu
option
3.
Select Reset Terminal WLAN Config.
4.
Follow the instructions on the terminal.
This will reset the terminal WLAN
configuration to its factory default setting.
configuration to its factory default setting.
FCC/IC COMPLIANCE
FCC ID: COL-NOIRE510W
IC: 2279B-NOIRE510W
Under Industry Canada regulations, this
radio transmitter may only operate using an
antenna of a type and maximum (or lesser)
gain approved for the transmitter by
Industry Canada. To reduce potential radio
interference to other users, the antenna
type and its gain should be so chosen that
the equivalent isotropically radiated power
(e.i.r.p.) is not more than that necessary for
successful communication.
This device complies with part 15 of the FCC
Rules. Operation is subject to the following
two conditions: (1) This device may not
cause harmful interference, and (2) this
device must accept any interference
received, including interference that may
cause undesired operation.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions:
(1) this device may not cause interference,
and (2) this device must accept any
interference, including interference that may
cause undesired operation of the device.
NOTE: This equipment has been tested and
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and,
if not installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the
equipment and receiver.
—Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced
radio/TV technician for help.
WARNING: Changes or modifications to the
equipment that are not expressly approved
by the responsible party for compliance
could void the user’s authority to operate
the equipment.
found to comply with the limits for a Class B
digital device, pursuant to part 15 of the
FCC Rules. These limits are designed to
provide reasonable protection against
harmful interference in a residential
installation. This equipment generates, uses
and can radiate radio frequency energy and,
if not installed and used in accordance with
the instructions, may cause harmful
interference to radio communications.
However, there is no guarantee that
interference will not occur in a particular
installation. If this equipment does cause
harmful interference to radio or television
reception, which can be determined by
turning the equipment off and on, the user
is encouraged to try to correct the
interference by one or more of the following
measures:
—Reorient or relocate the receiving antenna.
—Increase the separation between the
equipment and receiver.
—Connect the equipment into an outlet on a
circuit different from that to which the
receiver is connected.
—Consult the dealer or an experienced
radio/TV technician for help.
WARNING: Changes or modifications to the
equipment that are not expressly approved
by the responsible party for compliance
could void the user’s authority to operate
the equipment.
SAFETY INSTRUCTIONS
Electrical power supply network
Provide an A.C receptacle that meets the
following recommendations:
• Connector is installed near the equipment
and is easily accessible
510W
Wireless
Terminal
Terminal
USER GUIDE
NBS Payment Solutions Inc.
Corporate Headquarters - Canada
703 Evans Avenue, Suite 400
Toronto, Ontario, M9C 5E9
Canada
Tel: +1 416 621-7410
Fax: +1 416 621-2450
Fax: +1 416 621-2450