LEXIN ELECTRONICS INC LXFT4 Manual Do Utilizador
17
* If one unit has lost connection with another, the two units on the same channel
are still connected. Just follow the above connecting instruction to reconnect the
other disconnected unit when it is back in Intercom range.
* If one intercom rider goes out of range during a intercom talk, there may be
static and eventually the intercom will disconnect. In this case, th
e LX-FT4
automatically tries to reconnect the Intercom rider every eight seconds and you will
hear high tone double beeps until the connection is reestablished. you don’t want to
make a re-connection, press the Jog Dial button to stop the attempt.
* For four riders to successfully communicate, we suggest connecting the two
Bridge units that are paired using the B button first, then connect them to the End
units that are paired by A button. Since unit two and unit three act as a ‘bridge’ in
the chain we suggest keeping them within the stated intercom range to maintain
continuous communication.
Tips: To save battery power, disconnect the intercom units if you do not need to talk.
Important: The Bridge unit cannot be connected with a Bluetooth device (phone or
GPS) while it is being used as an Intercom Bridge.
5.4 Universal Pairing:
To enter pairing mode: Power on the LX-FT4, press and hold the B button for about 2
seconds until the LED begin flashing blue and red. Follow the other brand’s bluetooth
unit instructions to enter pairing mode also. Click the B button on LX-FT4 to pair.
Once pairing starts, the LED on the LX-FT4 unit will flash only blue. When the LED
is blinking blue on both units, then pairing is complete and successful.
To connect the LX-FT4 unit with the other: While in standby mode, double click the
B button on the LX-FT4 unit to connect. Once connected, the LED will flash 3 times
in blue every 3 seconds on LX-FT4 units.
To disconnect, click the Jog Dial on the LX-FT4 unit.
Note: You can only initiate the intercom from our LX-FT4 unit.
5.5 FM Radio
Turn on/off FM radio
When in standby, press and hold the A button for 2 seconds to turn on FM radio.
Press and hold it again for 2 seconds to turn off FM radio.
FM Radio Station Search
When in FM radio mode, press and hold the Jog Dial for one second to enter station
search mode, a beep tone will sound, within 10 seconds rotate the Jog Dial clockwise
for up search, counter clockwise for down search. After 10 seconds, it reverts to
volume control mode automatically and a beep tone will sound, or you can press &
hold the Jog Dial for 1 second to go back volume control mode.
are still connected. Just follow the above connecting instruction to reconnect the
other disconnected unit when it is back in Intercom range.
* If one intercom rider goes out of range during a intercom talk, there may be
static and eventually the intercom will disconnect. In this case, th
e LX-FT4
automatically tries to reconnect the Intercom rider every eight seconds and you will
hear high tone double beeps until the connection is reestablished. you don’t want to
make a re-connection, press the Jog Dial button to stop the attempt.
* For four riders to successfully communicate, we suggest connecting the two
Bridge units that are paired using the B button first, then connect them to the End
units that are paired by A button. Since unit two and unit three act as a ‘bridge’ in
the chain we suggest keeping them within the stated intercom range to maintain
continuous communication.
Tips: To save battery power, disconnect the intercom units if you do not need to talk.
Important: The Bridge unit cannot be connected with a Bluetooth device (phone or
GPS) while it is being used as an Intercom Bridge.
5.4 Universal Pairing:
To enter pairing mode: Power on the LX-FT4, press and hold the B button for about 2
seconds until the LED begin flashing blue and red. Follow the other brand’s bluetooth
unit instructions to enter pairing mode also. Click the B button on LX-FT4 to pair.
Once pairing starts, the LED on the LX-FT4 unit will flash only blue. When the LED
is blinking blue on both units, then pairing is complete and successful.
To connect the LX-FT4 unit with the other: While in standby mode, double click the
B button on the LX-FT4 unit to connect. Once connected, the LED will flash 3 times
in blue every 3 seconds on LX-FT4 units.
To disconnect, click the Jog Dial on the LX-FT4 unit.
Note: You can only initiate the intercom from our LX-FT4 unit.
5.5 FM Radio
Turn on/off FM radio
When in standby, press and hold the A button for 2 seconds to turn on FM radio.
Press and hold it again for 2 seconds to turn off FM radio.
FM Radio Station Search
When in FM radio mode, press and hold the Jog Dial for one second to enter station
search mode, a beep tone will sound, within 10 seconds rotate the Jog Dial clockwise
for up search, counter clockwise for down search. After 10 seconds, it reverts to
volume control mode automatically and a beep tone will sound, or you can press &
hold the Jog Dial for 1 second to go back volume control mode.