Adtran SFP 1490/1310nm 10km 1442110G1 Folheto
Códigos do produto
1442110G1
D
ESCRIPTION
The Small Form-Factor Pluggable (SFP) Gigabit
Ethernet, Single-Fiber is a bidirectional SFP that
installs into the Optical Loop Termination (OLT)
designed to accept SFPs. The SFP provides a single
optical interface to the GigE physical interface.
Installed into an appropriate OLT, the SFP provides a
Gigabit Ethernet interface to the supporting system.
Ethernet, Single-Fiber is a bidirectional SFP that
installs into the Optical Loop Termination (OLT)
designed to accept SFPs. The SFP provides a single
optical interface to the GigE physical interface.
Installed into an appropriate OLT, the SFP provides a
Gigabit Ethernet interface to the supporting system.
NOTE
To ensure compatibility, refer to the documentation
provided with the OLT.
provided with the OLT.
In a deployment consisting of an OLT with a
1442110G1 SFP installed; the Optical Network Unit
(ONU) should have a complementary 1442110G2 SFP
installed.
1442110G1 SFP installed; the Optical Network Unit
(ONU) should have a complementary 1442110G2 SFP
installed.
The following features are supported on the SFP:
♦
1000Base-LX 1490 nm Transmitter
♦
1000Base-LX 1310 nm Receiver
♦
Optical distance: 10 km maximum
Due to compliance certification requirements, only
SFPs supplied by ADTRAN should be used. ADTRAN
cannot certify system integrity with other SFPs.
SFPs supplied by ADTRAN should be used. ADTRAN
cannot certify system integrity with other SFPs.
OLT
1442110G1
1442110G2
ONU
Rx: 1310 nm
Tx: 1490 nm
Rx: 1490 nm
Tx: 1310 nm
Small Form-Factor Pluggable
1490 nm TX / 1310 nm RX, 10 km
Operational Specifications
♦
Optical Specifications:
◊
Transmit wavelength: 1490 nm
◊
Receive wavelength: 1310 nm
◊
Optical transmit level: –9 dBm to –3 dBm
◊
Optical receive level: –19.5 dBm to –3 dBm
◊
Optical distance: 10 km
◊
Optical connectors: LC
♦
Extended Environmental Support:
◊
Operational temperature range: –40°C to +85°C
◊
Storage temperature range: –40°C to +85°C
◊
Relative humidity to 95%, noncondensing
I
NSTALLATION
Prior to installation, inspect the SFP. If damage has
occured during shipping, file a claim with the carrier,
and then contact ADTRAN Customer Support. For
more information, refer to “Warranty”.
To install the SFP into an appropriate module,
complete the following steps:
occured during shipping, file a claim with the carrier,
and then contact ADTRAN Customer Support. For
more information, refer to “Warranty”.
To install the SFP into an appropriate module,
complete the following steps:
1. Insert the SFP into the SFP cage on the circuit
board of the host module with the latch handle
facing outward. Slide the SFP all the way into the
cage.
facing outward. Slide the SFP all the way into the
cage.
NOTE
The latch on the SFP is for removal only. When
removing the SFP, rotate the latch away from the
SFP, the SFP should slide easily out of the cage.
removing the SFP, rotate the latch away from the
SFP, the SFP should slide easily out of the cage.
2. Exert adequate pressure to ensure the SFP is
completely seated in the SFP cage.
3. Do not remove the connector plug until the
optical fiber connection is made.
It is recommended that the connector plug remain on
whenever the transciever optical fiber connector is
not inserted.
whenever the transciever optical fiber connector is
not inserted.
4. Continue the installation and turn-up of the host
module using the instructions in the Job Aid
provided with the module, or using the
Installation and Maintenance Practice (I&M)
available online at
provided with the module, or using the
Installation and Maintenance Practice (I&M)
available online at
www.adtran.com.
CLEI: BVL3ADJD_ _
Product P/N: 1442110G1
Product P/N: 1442110G1
Issue Date: 0812
Document P/N: 61442110G1-22A