AMX PS-POE-AT-TC FG423-84 Folheto

For full warranty information, refer to the AMX Instruction Manual(s) associated with your Product(s).

9/12

©2012 AMX. All rights reserved. AMX and the AMX logo are registered trademarks of AMX.

AMX reserves the right to alter specifications without notice at any time. 

3000 RESEARCH DRIVE, RICHARDSON, TX 75082 • 800.222.0193 • fax 469.624.7153 • technical support 800.932.6993 • www.amx.com

    93-0423-84  REV: A

•

The PS-POE-AT-TC “Data In” and “Data & Power Out” interfaces are 

qualified as Safety Extra-Low Voltage (SELV) circuits according to IEC 
60950-1. These interfaces may only be connected to SELV interfaces on 
other equipment.

WARNINGS!

•

The PS-POE-AT-TC should only be connected to devices compatible with 

this product. Using the PS-POE-AT-TC with incompatible devices may 
cause damage to the device.

•

Read the installation instructions before connecting the PS-POE-AT-TC to 

its power source.

•

Follow basic electricity safety measures before connecting the 

PS-POE-AT-TC to its power source.

•

A voltage mismatch can cause equipment damage and may pose a fire 

hazard. If the voltage indicated on the label is different from the power 
outlet voltage, do not connect the PS-POE-AT-TC to this power outlet.

Recycling and Disposal

Disposal instructions for old products. The WEEE (Waste Electrical and 
Electronic Equipment) national environmental initiatives have been put in 
place to ensure that products are recycled using best available treatment, 
and recovery and recycling techniques, to ensure human health and high 
environmental protection. Your product is designed and manufactured 
with high-quality materials and components which can be recycled and 
reused. Do not dispose of your old product in your general household 
waste bin. Inform yourself about the local separate collection system for 
electrical and electronic products marked by this symbol:

Use one of the following disposal options:

1.

Dispose of the complete product (including its cables, plugs, and 
accessories) in the designated WEEE collection facilities.

2.

If you purchase a replacement product, return your older product 
(including all components) back to the retailer. The retailer should accept 
it as required by the national WEEE legislation.

Installing the PS-POE-AT-TC

The PS-POE-AT-TC may be placed on a desktop.

Preliminary Steps

•

Ensure that AC power is applied to the PS-POE-AT-TC, using an 

operational ground connection.

•

Ensure that output Ethernet cable is connected to the DATA & POWER 

OUT port.

•

Verify that a power-ready Ethernet-compatible device is connected.

Before placing the PS-POE-AT-TC:

•

Do not cover the device or block the airflow to the device with any foreign 

objects. Keep the PS-POE-AT-TC away from excessive heat and 
humidity and free from vibration and dust.

•

Ensure that the cable length from the Ethernet network source to the 

terminal does not exceed 328 feet (100 meters). The device is not a 
repeater and does not amplify the Ethernet data signal.

•

The PS-POE-AT-TC does not have a power switch. Simply plug the 

device into an AC power source.

Installing the PS-POE-AT-TC

1.

Connect the PS-POE-AT-TC to an AC outlet (100-240VAC), using an 
appropriate power cord.

2.

Connect the DATA IN jack (input) to the remote Ethernet network switch’s 
Patch panel and the DATA & POWER OUT jack (output) to the terminal.

Pin Connections

FIG. 2 describes the PoE Gigabit pin-out connections for the IN and OUT 
Ports on the rear panel of the PS-POE-AT-TC: 

PoE Gigabit pin-out connections

(rear of unit)

POWER (+)

DATA

Pins 4/5 (DATA + PWR)

DATA

Pins 1/2 (DATA only)

DATA

Pins 3/6 (DATA only)

POWER (-)

DATA

Pins 7/8 (DATA + PWR)

Note:

= Transformer