Finder 19.41.0.024.0000 Relay (Feedback) 1 NO contact/(contact) 1 CO contact 24V DC/AC IP20 19.41.0.024.0000 Ficha De Dados
Códigos do produto
19.41.0.024.0000
5
2 NO (DPST-NO)
5/15
250/400
1,250
250
0.185
3/0.35/0.2
500 (10/5)
AgCdO
1 NO (SPST-NO)
100/10
24
24
24
1.6 (50 Hz)/0.8
(0.8…1.1) U
N
(0.8…1.1) U
N
–20…+50
IP20
Output specification (terminals 13-14-24)
Contact configuration
Rated current/Maximum peak current
A
Rated voltage/Maximum switching voltageV AC
Rated load AC1
VA
Rated load AC15 (230 V AC)
VA
Single phase motor rating (230 V AC)
kW
Breaking capacity DC1 (24/110/220 V)
A
Minimum switching load
mW (V/mA)
Standard contact material
Feedback output specification (terminals 53-54)
Contact configuration
Maximum / Minimum current
mA
Rated voltage
V AC/DC
Supply & Input specification
Nominal voltage (U
N
)
V AC (50/60 Hz)
V DC
Rated power
VA (50 Hz)/W
Operating range
AC
DC
Technical data
Ambient temperature range
°C
Protection category
Approvals (according to type)
19 Series - Override & Status indicating modules
Features
Override module - Auto/Off/Low/High
•
Override output module intended to permit the
automatic control of two-speed pumps, blowers
or motor groups. Or, in the case of installation,
maintenance or failure, to permit the load
equipment to be turned “Off“ or to run in “Low
speed“ or “High speed“ under “Hand“ control
automatic control of two-speed pumps, blowers
or motor groups. Or, in the case of installation,
maintenance or failure, to permit the load
equipment to be turned “Off“ or to run in “Low
speed“ or “High speed“ under “Hand“ control
•
4 function selector switch:
- Auto: directly controlled by the BMS or PLC
- Off: relays permanently Off
- Hand Low: Low speed relay output
- Auto: directly controlled by the BMS or PLC
- Off: relays permanently Off
- Hand Low: Low speed relay output
permanently On
- Hand High: High speed relay output
permanently On
•
24V AC/DC supply and module inputs
•
35 mm rail (EN 60715) mounting
Application examples:
•
control of two-speed pumps, blowers or motor
groups commonly associated with building
management systems
groups commonly associated with building
management systems
•
Low and High output contacts
•
1 feedback output contact
•
35 mm wide
•
LED indicator
19.42.0.024.0000
Wiring diagram
53-54 feed back information to the controller for Auto-operation
A3-A2 Low speed or power operation
A4-A2 High speed or power operation (dominating again low speed or low power operation)
T = ON delay for 13-14 and 13-24 is approx. 100 ms as pause for the speed shift.
By reserving motors with big moments of inertia (inertia force) from high speed to low speed an
additional ON delay of approx. 20 s is recommended.
A3-A2 Low speed or power operation
A4-A2 High speed or power operation (dominating again low speed or low power operation)
T = ON delay for 13-14 and 13-24 is approx. 100 ms as pause for the speed shift.
By reserving motors with big moments of inertia (inertia force) from high speed to low speed an
additional ON delay of approx. 20 s is recommended.
For outline drawing see page 11
Request
Response
LED Signals
Auto-Operation
Intervention-(Manual-)Operation
Switch position:
Controller, PLC
Type 19.42
VI-2012, www
.finder
net.com