Ansmann Mini-alarm System with Remote Control 323 Ficha De Dados
Códigos do produto
323
b) Batteries
• Correct polarity must be observed while inserting the batteries.
• Batteries should be removed from the device if it is not used for a long period of
• Batteries should be removed from the device if it is not used for a long period of
time to avoid damage through leaking. Leaking or damaged batteries might cause
acid burns when in contact with skin, therefore use suitable protective gloves to
handle corrupted batteries.
• Batteries must be kept out of reach of children. Do not leave batteries lying around,
as there is risk, that children or pets swallow them.
• All batteries should be replaced at the same time. Mixing old and new batteries in
the device can lead to (rechargeable) battery leakage and device damage.
• Batteries must not be dismantled, short-circuited or thrown into fire. Never recharge
non-rechargeable batteries. There is a risk of explosion!
c) Miscellaneous
• Consult an expert when in doubt about operation, safety or connection of the
device.
• Maintenance, modifications and repairs are to be performed exclusively by an
expert or at a qualified shop.
• If you have questions which remain unanswered by these operating instructions,
contact our technical support service or other technical personnel.
Operating elements
Remote controller Main unit
Mounting bracket
1
2
2
4
5
6
6
7
8
3
1 Remote signal transmitter
5 PIR motion detector
2 Remote control status LED 6 Green status LED
3 Mode selection button
7 Buzzer
4 Remote signal receiver
8 Red status LED
Battery replacement
a) Main unit
1. The batteries are used as back-up power source only. The main unit must be connected
with a suitable 9 V/DC power adapter (not included) during operation.
2. Slide out the battery compartment cover located at the back of the main unit.
3. Insert four AA batteries (Mignon) while observing the correct polarity (“+” = positive;
3. Insert four AA batteries (Mignon) while observing the correct polarity (“+” = positive;
“–” = negative).
4. Close the battery compartment cover.
When the voltage is decreasing, the low battery alarm will be activated as followed:
When the voltage of the backup batteries is low (e.g. 3.5 to 4.0 V), a beep sounds
every 6 seconds until the batteries are empty or replaced. The beep only sounds if
the alarm has not been activated.
b) Remote control
1. Unscrew the screw, which located at the back of the remote control to open the remote
control
2. Insert three AG13 button cells while observing the correct polarity (“+” = positive; “–” =
negative).
3. Re-assemble the remote control.
Mounting and detection area
The main unit can be mounted on wall with the mounting bracket.
1. Use the mounting bracket as a template to mark positions on the wall.
2. Drill two screw holes and insert the included wall plugs.
3. Affix the mounting bracket on the wall with the provided screws
4. Attach the mounting bracket to the back of the main unit.
Otherwise, the main unit can be placed on a level and sturdy surface. The
1. Use the mounting bracket as a template to mark positions on the wall.
2. Drill two screw holes and insert the included wall plugs.
3. Affix the mounting bracket on the wall with the provided screws
4. Attach the mounting bracket to the back of the main unit.
Otherwise, the main unit can be placed on a level and sturdy surface. The
optimum installation location is 2m from the floor at 15º. The PIR motion
detector (5) can cover 6m in radius and 90º horizontally and 20º vertically.
2m
15º
PIR alarm with remote control
Version 07/14
Item no. 751170
Intended use
The PIR alarm is intended to alert the resident if an intruder is detected within the area covered
by the PIR sensor. The sensor detects motion by sensing the heat emitted from an object
moving across its detecting area. The alarm has been fine tuned so that false alarms are
minimal. It is armed/ disarmed by remote control and is equipped with a powerful 110dB audio
alarm.
The main unit must be connected with a suitable 9 V/DC power adapter (not included) during
The main unit must be connected with a suitable 9 V/DC power adapter (not included) during
operation. 4 pieces 1.5 V/DC batteries type AA (not included) serve as back-up batteries, in
case of a short term mains power failure.
The main unit should be operated in dry indoor or protected outdoor area. It is ideal for
The main unit should be operated in dry indoor or protected outdoor area. It is ideal for
apartment, garage, shed, caravan or boat.
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
For safety and approval purposes (CE), you must not rebuild and/or modify this product. If you
use the product for purposes other than those described above, the product may be damaged.
In addition, improper use can cause hazards such as short circuiting, fire, electric shock etc.
Read the instructions carefully and keep them. Make this product available to third parties only
together with its operating instructions.
This product complies with the statutory national and European requirements. All company
This product complies with the statutory national and European requirements. All company
names and product names are trademarks of their respective owners. All rights reserved.
Delivery content
• PIR alarm
• Mounting bracket
• Remote control
• 3 x 1.5 V/DC button cells
• 2 x screws, 2 x wall plugs
• Operating instructions
• Mounting bracket
• Remote control
• 3 x 1.5 V/DC button cells
• 2 x screws, 2 x wall plugs
• Operating instructions
Safety instructions
Read the operating instructions carefully and especially observe the safety
information. If you do not follow the safety instructions and information
on proper handling in this manual, we assume no liability for any resulting
personal injury or damage to property. Such cases will invalidate the warranty/
guarantee.
a) Persons / Product
• The device is not a toy. Keep it out of the reach of children and pets.
• Do not leave packaging material lying around carelessly. These may become
• Do not leave packaging material lying around carelessly. These may become
dangerous playing material for children.
• Protect the product from extreme temperatures, direct sunlight, strong jolts, high
humidity, moisture, flammable gases, vapours and solvents.
• Do not place the product under any mechanical stress.
• If it is no longer possible to operate the product safely, take it out of operation and
• If it is no longer possible to operate the product safely, take it out of operation and
protect it from any accidental use. Safe operation can no longer be guaranteed if
the product:
- is visibly damaged,
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
- is no longer working properly,
- has been stored for extended periods in poor ambient conditions or
- has been subjected to any serious transport-related stresses.
• Please handle the product carefully. Jolts, impacts or a fall even from a low height
can damage the product.
• Also observe the safety and operating instructions of any other devices which are
connected to the product.
• The main unit should be placed away from heaters, ovens and other sources of
heat.
• The main unit should not be directed toward heaters, fans, air exhaust or clothes
dryer, air conditioner, open window, direct sunlight, swimming pool, pond, luminous
sign. Any kind of temperature change can cause spurious detection.