Carson BRUSHLESS-SET DRAGSTER SPORT RTR 14 T 500906159 Manual Do Utilizador
Códigos do produto
500906159
12
GB
CARSON DRAGSTER Brushless-Sport „Water resistant Version“ • 50 090 6158
c. Program the ESC
a) Program by the ESC “SET” key
Alert Tones
a) Input voltage abnormal alert tone:
The ESC begins to check the input voltage when power on, if it is out
of the normal range, such an alert tone will be emitted:
of the normal range, such an alert tone will be emitted:
“beep-beep-, beep-beep-, beep-beep-” (There is 1 second time inter-
val between every “beep-beep-” tone).
val between every “beep-beep-” tone).
b) Throttle signal abnormal alert tone:
When the ESC can’t detect the normal throttle signal, such an alert
tone will be emitted:
tone will be emitted:
“beep-, beep-, beep-” (There is 2 seconds time interval between every
“beep-” tone).
“beep-” tone).
Protection Function
a) Low voltage cut-off protection: If the voltage of a lithium battery
pack is lower than the threshold for 2 seconds, the ESC will cut of the
output power. Please note that the ESC cannot be restarted if the
voltage of each lithium cell is lower than 3.5V.
pack is lower than the threshold for 2 seconds, the ESC will cut of the
output power. Please note that the ESC cannot be restarted if the
voltage of each lithium cell is lower than 3.5V.
For NiMH battery packs, if the voltage of the whole NiMH battery pack
is higher than 9.0V but lower than 12V, it will be considered as a 3 cell
lithium battery pack; If it is lower than 9.0V, it will be considered as a 2
cell lithium battery pack.
is higher than 9.0V but lower than 12V, it will be considered as a 3 cell
lithium battery pack; If it is lower than 9.0V, it will be considered as a 2
cell lithium battery pack.
For example, if the NiMH battery pack is 8.0V, and the threshold is set
to 2.6V/Cell, so it will be considered as a 2 cell lithium battery pack,
and the low-voltage cut-off threshold for this NiMH battery pack is
2.6*2=5.2V.
to 2.6V/Cell, so it will be considered as a 2 cell lithium battery pack,
and the low-voltage cut-off threshold for this NiMH battery pack is
2.6*2=5.2V.
b) Over-heat protection: When the temperature of the ESC is over a
factory preset threshold for 5 seconds, the ESC will cut off the output
power. You can disable the over-heat protection function for competition
race.
factory preset threshold for 5 seconds, the ESC will cut off the output
power. You can disable the over-heat protection function for competition
race.
c) Throttle signal loss protection: The ESC will cut off the output
power if the throttle signal is lost for 0.2 second.
power if the throttle signal is lost for 0.2 second.
Turn off the ESC,
Turn on the transmitter
Hold the SET key,
Switch on the ESC
Red LED flashes
Green LED flashes
for 1 time
......The following steps are just like the above steps......
Finish pr
og
ramming
ramming
, swit
ch off the ESC, and then swit
ch it on
Green LED flashes
for 2 times
Green LED flashes
for 3 times
Green LED flashes
for N times
Enter the N
th
item
Enter the 3rd item
„Low Voltage Cut-Off“
Enter the 2nd item
„Drag Brake Force“
„Drag Brake Force“
Enter the 1st item
„Running Mode“
Enter the corresponding
programmable item, the RED
LED flashes for several times,
the times presents the current
value of this item.
programmable item, the RED
LED flashes for several times,
the times presents the current
value of this item.
Press the SET key to choose the programmable
value, the RED LED flashes for several times, the
times presents the serial number of the value you
are choosing.
value, the RED LED flashes for several times, the
times presents the serial number of the value you
are choosing.
Red LED flashes for 1 time to choose
„Forward with brake“
Red LED flashes for 2 times to choose
„Forward/Reverse with brake“
„Forward with brake“
Red LED flashes for 2 times to choose
„Forward/Reverse with brake“
Red LED flashes 1 time, choose „0%“
Red LED flashes 2 times, choose „5%“
Red LED flashes 3 times, choose „10%“
Red LED flashes 4 times, choose „20%“
Red LED flashes 5 times, choose „40%“
Red LED flashes 6 times, choose „60%“
Red LED flashes 7 times, choose „80%“
Red LED flashes 8 times, choose „100%“
Red LED flashes 2 times, choose „5%“
Red LED flashes 3 times, choose „10%“
Red LED flashes 4 times, choose „20%“
Red LED flashes 5 times, choose „40%“
Red LED flashes 6 times, choose „60%“
Red LED flashes 7 times, choose „80%“
Red LED flashes 8 times, choose „100%“
Red LED flashes 1 time, choose „None“
Red LED flashes 2 times, choose „2.6V“
Red LED flashes 3 times, choose „2.8V“
Red LED flashes 4 times, choose „3.0V“
Red LED flashes 5 times, choose „3.2V“
Red LED flashes 6 times, choose „3.4V“
Red LED flashes 2 times, choose „2.6V“
Red LED flashes 3 times, choose „2.8V“
Red LED flashes 4 times, choose „3.0V“
Red LED flashes 5 times, choose „3.2V“
Red LED flashes 6 times, choose „3.4V“
Press SET key to choose the value, the flash
times of RED LED means the serial number
of the value (1 time means the 1st value, 2
times means the 2nd value...)
times of RED LED means the serial number
of the value (1 time means the 1st value, 2
times means the 2nd value...)
Hold SET key for 3 seconds
Hold SET key for 3 seconds
Hold SET key for 3 seconds
Release
SET key
SET key
Press
SET key
SET key
Press
SET key
SET key
Press
SET key
Press
SET key
Release
SET key
SET key
Release
SET key
SET key
Release
SET key
SET key