Carson BRUSHLESS-SET DRAGSTER SPORT RTR 14 T 500906159 用户手册

a)  Program by the ESC “SET” key

a) Input voltage abnormal alert tone: 

The ESC begins to check the input voltage when power on, if it is out 
of the normal range, such an alert tone will be emitted: 

“beep-beep-, beep-beep-, beep-beep-” (There is 1 second time inter-
val between every “beep-beep-” tone).

b) Throttle signal abnormal alert tone: 

When the ESC can’t detect the normal throttle signal, such an alert 
tone will be emitted:

“beep-, beep-, beep-” (There is 2 seconds time interval between every 
“beep-” tone).

a) Low voltage cut-off protection: If the voltage of a lithium battery 
pack is lower than the threshold for 2 seconds, the ESC will cut of the 
output power. Please note that the ESC cannot be restarted if the 
voltage of each lithium cell is lower than 3.5V.

For NiMH battery packs, if the voltage of the whole NiMH battery pack 
is higher than 9.0V but lower than 12V, it will be considered as a 3 cell 
lithium battery pack; If it is lower than 9.0V, it will be considered as a 2 
cell lithium battery pack. 

For example, if the NiMH battery pack is 8.0V, and the threshold is set 
to 2.6V/Cell, so it will be considered as a 2 cell lithium battery pack, 
and the low-voltage cut-off threshold for this NiMH battery pack is 
2.6*2=5.2V.

b) Over-heat protection: When the temperature of the ESC is over a 
factory preset threshold for 5 seconds, the ESC will cut off the output 
power. You can disable the over-heat protection function for competition 
race.

c) Throttle signal loss protection: The ESC will cut off the output 
power if the throttle signal is lost for 0.2 second.

Turn off the ESC,

Turn on the transmitter

Hold the SET key,

Switch on the ESC

Red LED flashes

Green LED flashes

for 1 time

......The following steps are just like the above steps......

Finish pr

og
ramming

, swit

ch off the ESC, and then swit

ch it on

Green LED flashes

for 2 times

Green LED flashes

for 3 times

Green LED flashes

for N times

Enter the N

th

 item

Enter the 3rd item

„Low Voltage Cut-Off“

Enter the 2nd item
„Drag Brake Force“

Enter the 1st item

„Running Mode“

Enter the corresponding 
programmable item, the RED 
LED flashes for several times, 
the times presents the current 
value of this item.

Press the SET key to choose the programmable 
value, the RED LED flashes for several times, the 
times presents the serial number of the value you 
are choosing.

Red LED flashes for 1 time to choose 
„Forward with brake“
Red LED flashes for 2 times to choose 
„Forward/Reverse with brake“

Red LED flashes 1 time, choose „0%“
Red LED flashes 2 times, choose „5%“
Red LED flashes 3 times, choose „10%“
Red LED flashes 4 times, choose „20%“
Red LED flashes 5 times, choose „40%“
Red LED flashes 6 times, choose „60%“
Red LED flashes 7 times, choose „80%“
Red LED flashes 8 times, choose „100%“

Red LED flashes 1 time, choose „None“
Red LED flashes 2 times, choose „2.6V“
Red LED flashes 3 times, choose „2.8V“
Red LED flashes 4 times, choose „3.0V“
Red LED flashes 5 times, choose „3.2V“
Red LED flashes 6 times, choose „3.4V“

Press SET key to choose the value, the flash 
times of RED LED means the serial number 
of the value (1 time means the 1st value, 2 
times means the 2nd value...)

Hold SET key for 3 seconds

Hold SET key for 3 seconds

Hold SET key for 3 seconds

Release
SET key

Press
SET key

Press
SET key

Press

SET key

Press

SET key

Release
SET key

Release
SET key

Release
SET key